Your cart is empty.
Your cart is empty.4.6 out of 5 stars
- #125,426 in Tools & Home Improvement (See Top 100 in Tools & Home Improvement)
- #142 in Ceiling Fan Remote Controls
Product Description
Universal Receiver of Ceiling Fan
This FAN28R receiver works for most 110V 3-speed AC ceiling fans, compatible with Hampton Bay, Harbor Breeze, Hunter, Honeywell and other ceiling fans.
Light dimmer of this FAN28R receiver compatible with incandescent light bulbs and some dimmable LED lamps.
Most LED lights and all CFL lights are non-dimmable, light dimmer only supports the ON/OFF function in that case, and it may cause to flicker when using the dimming function.
This FAN28R receiver of ceiling fan remote control is designed to separately control your ceiling fan speed(HI, MED, LOW, OFF) and light brightness(ON, OFF, DIMMING). It to work with ceiling fan that requires a remote control (Not included).
Compatibility of Receiver
Replacement for these receiver models:
FAN28R, FAN18R, 28R, 18R.
Works with these remote FCC ID / Models:
2AAZPFAN53T, FAN-53T, L3HFAN11T, FAN-11T, KUJCE9103, CHQ7030T, UC7030T,
2AAZPFAN35TI, L3HFAN35T, FAN-35T, L3HFAN35T1, FAN-35T1, L3HFAN51T, FAN-51T,
L3H2010FANHD, FAN-HD, L3H2014FANHD, HD5, Standard-RR7079T
Not compatible with Reverse version.
Note:
Please make sure your remote matches this receiver before buying. If not sure, we recommend to purchase a complete kit in our store.
Easily Replace Your Lost, Broken or Dirty Ceiling Fan Receiver
There are 2 ways to pair your new COREBAY ceiling fan receiver with remote.
1. Match DIP settings from your old receiver to your new receiver.
2. Find the DIP settings on the remote to match them with your receiver.
Easy to Install
1. Setting the codes on the remote control and receiver
NOTE: It is imperative that the code used for both transmitter and receiver is exactly the same, otherwise remote controller will not work.
This unit has 16 different code combinations(0000, 0001, 0010, 0100, 0110, 0101, 0011, 0111, 1111, 1110, 1101, 1011, 1001, 1010, 1100, 1000).
The default settings is 0000, and it is not recommended.
2. Installing receiver in ceiling fan
WARNING: To reduce the risk of fire or electric shock, remember to disconnect power. The electrical wiring must meet all local and national electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0, Maximum light watts: 240w
NOTE: Do not use this product in conjunction with any variable wall control. Incorrect wire connection can damage this receiver.
3. Operating transmitter
Install a 9V battery (Not included) in the remote (Not included), and you can control your fan now.
More information please refer to the operation instructions in the package.
Peter Chadwick
Reviewed in the United States on March 5, 2025
Works great
Brenton
Reviewed in Canada on January 17, 2025
This remote uses a standard 9V battery not a crazy special and expensive 12V.
Cornhusker
Reviewed in the United States on August 6, 2024
We had a 40+ year old fan. Finally the remote would not activate the lights. We found just the controller for this fan - it matched by part # with the existing remote. We decided to order the package of the controller + remote as a precaution. Good thing we did. The old remote would not activate the new controller - however the new remote works fine. We have extensive experience in electrical devices so this was easy to install. Good documentation & wiring diagrams. It even included wire nuts & connectors. We should be good for a long time.
Jan A.
Reviewed in the United States on August 25, 2024
All I had to do was program this one just like my old one (there is a little thing to do this inside of the remote near the battery compartment with four numbered levers that you can move) and it worked immediately; it could not have been easier and I was thrilled!
Rumplestiltskin
Reviewed in the United States on May 29, 2024
I did not replace the remote stick; stuck with the existing unit and just set the new receiver's DIP switches to match the remote's. Switched off the circuit breaker and swapped out the old receiver for the new one. Not a lot of room up there but, with a few nudges and movement of the wires, it fit and I was able to close up the canopy. Switched on the circuit breaker and used the old remote. The fan (all three speeds) and light work as intended. Fairly cheap fix for the dead receiver (only 14 months old) that came with my Hampton Bay fan. I'll keep the replacement remote in a drawer in case the old one dies.
Alain Nadeau
Reviewed in Canada on December 4, 2024
fonctionne très bien
JR
Reviewed in the United States on December 26, 2024
This remote fixed the issues I was having with my fan. However, the hand unit is bulky and old fashioned in its design.
Customer
Reviewed in Canada on December 21, 2024
The media could not be loaded.
fred b.
Reviewed in Canada on November 6, 2024
Our Hampton Bay ceiling fan was purchased in 2017 and has been running nonstop since.It was great that we could get a new remote although we didn't need the receiver.
Hippie67
Reviewed in the United States on November 10, 2024
Was selling my house and of course the remote decided to die. Bought this and popped it in. Worked great. Didn't cost a fortune. Love it.
Gabethebabe120456
Reviewed in the United States on October 28, 2024
Was an easy install work perfectly. Performing well
Mary C.
Reviewed in Canada on October 2, 2024
I would avoid this replacement kit. We bought this kit because our original Hampton Bay receiver started to delay the light and fan from turning on and off. The remote and receiver work ok at first. About a week after the installation the light started to “strobe”, quickly dimming and brightening. We reinstalled the original receiver, we still have a delay in working however the stobing stopped. It should be noted that the original Hampton Bay remote did not work well with the receiver in this kit, it could only turn the lights on and off, unable to control the fan.
Kate M.
Reviewed in the United States on May 20, 2020
We needed an extra remote for our Casa Vieja Desteny ceiling light and fan, which says it is a uc7080t1 or uc7080t remote. If you buy it from the manufacturer, it's $30+. But this remote was half that price, has all the same features, includes a holder, and required no set up. (Fortunately the four pins were already set on the same frequency as our fan). You do need to buy a 9V battery however - none is included
Recommended Products
$52.46
$ 25 .99 $25.99