Aufrüsten meines MacBook Air 2017 hat super funktioniert.Das der Adapter zu dick aufträgt und die Unterseite sich nicht mehr verschließen lässt kann ich nicht bestätigen. Bei mir hat alles gepasst. Ebenso die Passgenauigkeit der Schraubenbohrung. Vielleicht wurde hier aufgrund der schlechteren Rezessionen nachgebessert.Verwendet wurde ein aktuellerCrucial P3 1TBMacBook Air 2017 (MacOS Monterey)Boot Stick mit MacOS Mojave, erstellt mit Windows.Festplatte musste nach dem Bootvorgang über das Festplattendienstprogramm lediglich formatiert werden und war dann auch verwendbar für die Installation.Alles machbar für jemanden der sich mit so etwas eigentlich nicht auskennt.

I ordered this for my 2015 15” MacBook Pro. It fits perfectly and works great. I read online after I bought it and it shipped that I would need a short adapter so I was prepared to return it, but tried it anyway. Works and fits perfectly no problems with speed or anything else. I recommend it for a MacBook Pro. I bought the longer version because I was worried about my ssd shorting out if it wasn’t insulated from the logic board.

Works as expected with my crucial p3

Worked perfectly well and quite easy to install. The compatibility and installation guide provided on the product page is super helpful. I tried this adapter with a Samsung 980 1TB (MZ-V8V1T0) SSD, and it worked flawlessly. This helped me upgrade to upgrade from 256GB to 1TB.The information and compatibility guide provided on this page is quite useful. I would also suggest to watch some related you tube videos as well.

Funciona perfectamente con iMac 27" de 2017 junto a un SSD M2 de Crucial P3 2TB (pese a no aparecer en la lista de compatibilidad). Alcanza velocidades de lectura y escritura máximas según especificaciones de Crucial. ¡No te olvides de activar compatibilidad con TRIM!

This adapter fit and worked PERFECTLY! I used it in a “mid-2014” MacBook Pro 13” Retina, version “MacBookPro 11,1”, model number A1502.It was relatively easy. - at least compared to any later MacBook. Take the bottom plate off the computer (10 tiny proprietary pentalobe screws, IIRC). Take the old, slow, small capacity (in my case, a 128GB) out (one T5 screw). I placed a new 1TB Crucial P2 NVMe SSD in the adapter, firmly clicked the adapter in the slot in the computer, replaced the screw, and screwed the bottom plate back in place. Hardware upgrade complete!The trickier part in some ways is re-initializing the new drive and reinstalling a fresh new operating system. I had planned ahead. I booted from an external USB-3 SSD loaded with various macOS installers - in this case, macOS 11 “Big Sur” is the highest one can install on said machine (without hacks, but that’s another story). After correctly choosing the default (and required) APFS to format the drive, Big Sur installed without a hitch in a few minutes. A few security updates should install after rebooting. Set your preferences and Boom, done!Bottom line: Easy to install if you have patience, steady hands, and some experience working on computers with tiny tools; an external SSD; and basic knowledge of installing operating systems. HUGE savings over an Apple proprietary drive or questionable Chinese knockoff drives using the old interface.P.S. Note that there is at least one brand of competing adapter on Amazon for a couple bucks less. I bought one - it didn’t work and it was visibly poorer quality.

Después de varios tutoriales en youtube llegue con este adaptador que funciono a la primera, no batalle nada para cambiar mis 128Gb a 1Tera. Compre 2 tipos de discos, un Samsung EVO 970 de 500Gb y un Crucial de 1Tb. ambos me funcionaron correctamente. Mi Macbook tiene vida para muchos años más.El único pero que puedo darle es la presentación, aunque viene en una bolsita sellada antiestática y con una espuma de protección, deberían mandarlo en caja, y no en sobre para evitar que se vaya a doblar.

I combined this $16 Sintech card adapter with a 2TB SDD from TopMore for $215... and wow, the upgraded performance results are impressive. No glitches or side effects of any kind.The installation process was straight forward:1. Make USB install drive from latest MacOS2. Manual back up original SSD via Time Machine3. Power down4. Remove bottom tray with T5 driver/bit5. Disconnect battery from logic board6. Remove original SSD* with T5 driver/bit7. Insert new SSD into Sintech adapter, and install into logic board with Phillips driver/bit8. Reconnect battery9. Restore bottom tray with T5 driver/bit10. Boot from USB to format new SSD and install MacOS11. Login and use Migration Assistant to restore apps and files from Time MachineIt's a relatively simply process that can be done by anyone with any computer experience or even the slightest willingness to learn. There are all kinds of videos on YouTube which show the basics of opening up the laptop for upgrading various components, so you'll have some idea what you're getting into... and you'll see that while it requires great care, it is not difficult.(*In my particular case, I hit a huge problem when I discovered the original SSD was held in by a stripped screw which I could not remove with a driver/bit. After a little trial and error, the only workable solution was to grab a power drill and drill it out. Obviously, I had to take great care with that process, given the consequence of any mistake, but it ultimately removed the stripped screw and allowed me to complete the upgrade. You won't have the problem I encountered, but the story serves the purpose of demonstrating that if I can overcome the disaster of finding a stripped screw inside the machine, then you'll be able to workaround any unexpected hiccups too. Just take your time.)

Ordered two a while ago.. and Amazon didn't ship both. Vendor responded quickly to my complaint and shipped out missing adapter quickly. I couldn't ask for better service.I'm also pretty sure they've added more guidance to the product listing (this Amazon listing) about supported hardware and troubleshooting since my original purchase, so nice to see them continuing to add to their support documentation.I'll waste some of my plentiful shelter-at-home time with installation tips and my detailed experience with these adapters below.. but I'll wrap up the short-version of my review by saying...Bought two already and I'm ordering more to upgrade additional 'retired' iMacs that have come into my office (University IT Support). There's plenty of usefulness in a 2015 17" iMac after it's got a new NVMe drive in it.Long Version...Installation is not trivial, but that's because of how iMacs are designed and assembled.Read a tear-down webpage, take your time and don't force the screen. They're not that hard to crack (I've done it.. and I'm a professional ;-P ).I find, in addition to a plastic cards (old gift card or similar works well).. I like to use an Exacto Knife so carefully slice through the adhesive foam gasket (slowly slice down into gasket in increasingly deep passes, don't jam blade between glass and case).I also like using increasingly thick guitar picks as shims as I work around from top->down sides.. and look for pull-away tabs at outside of bottom gasket section on newer iMacs.Even thought you have to completely gut the iMac's insides to get to the SSD interface on the back of the board, the actual installation of this adapter is easy so I gave it 5-stars.Oh yea, if you don't want to buy a replacement gasket kit.. don't use double-sided tape instead. It's not thick enough to make contact with screen and case. just wrap some tape around outside edge of glass and case.As for how will it works... Pick a supported SSD, avoid the Samsung drives that they warn against using.. and it just works. You can't ask for more.My own results are mixed so far. .but I don't blame Sintech.. and I believe they recently posted a fix for the one issue I'm still having (I'll try today).- 2017 27" iMac: Even though this isn't listed as a supported Model, the adapter works fine in my 2017 iMac.Before upgrade, it was unstable and I noticed some serious errors with the Fusion Drive B-Tree structure, so I pulled both the disk & Apple SSD and upgraded to a FireCuda NVMe drive. Instability persisted but cleared up after I also pulled a pair of 3rd party SO-DIMMs. I suspect both Fusion Drive issues (which Crash Logs pointed to) and a bad pair of SODIMMs both contributed to original problems. iMac runs better than new now (though still short some RAM).- 2015 27" iMac: Again, I replaced a fusion set that was causing problems in this iMac. This iMac also seemed to be having problems with it's Fusion Drive setup prior to upgrading.Installation and clean-install on new drive went flawlessly and iMac worked great.. except it then started crashing when going to sleep. I've since seen new info here on a possible fix so I'll give that a try.. though it'll take me a while to confirm the issue is gone since it was an intermittent problem.No indication that there's a problem with the adapter/drive while the computer is in use though.One thing to note if you plan to replace a Fusion drive set with this...If you use CarbonCopy Cloner (or presumably Disk Utility too) to clone your Fusion drive Volume to a disk image or to your new NVMe drive, it clones the 2-drive Fusion formatting too. You'll end up with two partitions on your single NVMe.. with one staging new & frequently-used data.. and older data getting migrated to the 2nd partition. It'll look like one Drive from the Finder, but I have suspicions that Apple's data staging code is introducing corruption into Fusion Drive's directory B-Tree so best to not introduce this un-needed complexity.Better options...1. If you've got.an up-to-date TimeMachine backup.. do a clean Mac OS install onto new drive and a data migration from your TimeMachine backup..or...2. Get an external USB NVMe adapter or NVMe USB case..Do an internet recovery (boot w/ Command-R pressed) and install a clean version of MacOS onto the new NVMe drive (usb-connected)..Boot off the NVMe drive and update to latest OS if you need to (I've seen Internet recovery install latest Mac OS release on some Macs, and older versions on others)..Now, do a Data Migration from the Fusion Drive set to the new NVMe.When it's all setup.. then pull the iMac apart and swap the drives.Good luck.. Steve.