Your cart is empty.
Your cart is empty.Product Description
Thick Gold Finger
Anti-scratch and wear-resistant, with more solid contact points to ensure stable data transmission.
LED Indicator
Real-time monitoring of working status.
Excellent Heat Dissipation
With heat sink can reduce the temperature quickly and maintain the stability of network transmission.
ASMedia ASM1166 Controller
Use ASMedia ASM1166 chip to make transmission more stable, speed up data processing, and ensure stable and efficient data transmission.
Jonah A.
Reviewed in the United States on February 27, 2025
This device works for me! I am running Proxmox 8.3.0. I currently have 4 drives connected to this host bus adapter and the 4 drives are running in ZFS RaidZ2. So far no issues!Something important to keep in mind is that while this is a PCI-E x4 card and it says it supports PCIE Version 3. The actual controller within this unit is talking upstream to your processor or north bridge at PCIE Version 2 X2 speeds. This is roughly 1 GB/s if you don't account for any communication overhead. This card will extract the maximum speed out of Non-SSDs and drives that are running in raid that don't boost the write speed. I would highly suggest plugging in high speed drives directly into your motherboards sata headers.
Steve A. Asher
Reviewed in the United States on February 23, 2025
I had 2 different ones in and I lost one of my DVD Recorders. One of them had 4 ports and the other had 2. Now I have more breathing space for my Video Card.
Sterling TS
Reviewed in the United States on February 18, 2025
Replaced an earlier card that was no longer working and about 6 yrs old. This was flawless. No drivers needed to be installed. Speed is quite good. I can get between 250-260MBs when copying from a fast source file and the flies are large.I have all ports in use. It has been rock steady!
Dissolution
Reviewed in the United States on February 11, 2025
This card worked perfect, was super easy to install, and the additional SATA cables were a great touch. Would highly recommend. It comes with two mounting brackets so it will work on anything besides a laptop.
J Allison
Reviewed in the United States on January 16, 2025
Upgraded motherboard and newer ones all seem to have reduced SATA ports in favor of USB. Went from 10 SATA (9 used) to 4 and needed an adapter like this. The new board has a PCIe x 4 slot, so this was a perfect match. All drives work perfectly and you wouldn't know the adapter was even there.
True customer
Reviewed in India on September 6, 2024
Received the product, this seemed in good condition with proper packing and seal. After installing got the Secure Boot Error message that the system has found unauthorized changes on the firmware of this device. See the attached picture.Is there way to get the authentic firmware re-flashed on this device?Update: Contacted 10Gtek support team and came to know that there is no supported way to update the firmware of this card. IMO, there is no point of buying this card for use given the security risk!
Sing
Reviewed in the Netherlands on September 21, 2024
Doesn't work.Bricked 2 SSD's i've connected to it.
Käufer8600
Reviewed in Germany on August 9, 2024
Eingesteckt, vom Bios sofort erkannt. Arbeitet bisher zuverlässig mit 2 SSD SATA.Benötigt eine X4-PCIe Steckplatz.Laut Info nicht bootfähig für Betriebssystem (nicht getestet).Leider fehlt jedwede Beschreibung (auch, ob man mittels einer Tasten-Kombination ins Steckkarten Bios gelangt).
Good quality, easy to assemble
Reviewed in Belgium on August 22, 2024
Work as it should, great for older systems with pcie 2.0 where 1x doesnt provide enough bandwidth for 4 drives.
Vitamin D
Reviewed in the United States on December 7, 2024
My Sil3132 PCIe x1 cards aren't recognized by my new Z790 MoBo no matter what I do in the BIOS. I tried a NewerTechnology card with 4 eSATA ports and a Marvell 9235 chip and it worked, but had an annoying BIOS setup screen that I couldn't bypass.This card is exactly what I needed. I have a 10-bay hot-swap eSATA enclosure with ten 16 TB drives. I set both ports on the card with the jumpers to run the external ports. Both ports multiply and I get fantastic speeds with no issues performing multiple copies simultaneously through either ports or from one to the other.The trick with newer UEFI motherboards is to set the mode from UEFI to CSM and then the boot type to UEFI with Legacy. These settings might be slightly different based on manufacturer and BIOS revision. So you'll have to play around to get it right. But my board flashes the ASMedia BIOS screen and shows the detected drives in a couple of seconds then moves on to boot up. I disabled all LEGACY boot devices so Windows doesn't scan these drives to find a suitable boot device.This is exactly what I wanted... a 10 drive port multiplier through eSATA that works on UEFI motherboards in Windows 11.
David
Reviewed in the United Kingdom on December 23, 2024
Good product, does what it says, stable in old Pc, decent upgradeWorks far better than a couple of others tried n returned
Steve P
Reviewed in the United States on October 12, 2024
Does exactly what it says - completely plug-n-play providing multiple additional sata3 ports.I've seen some with metal reinforced housing, making it not flex as much when sata cables are inserted. Certainly not a necessary feature - I had no issues.
William F. Cleveland
Reviewed in the United States on June 21, 2023
This card 10Gtek PCIe SATA Card 4 Port with 4 SATA Cables and Low Profile Bracket, 6Gbps SATA3.0 Controller PCI Express Expansion Card, X2, Support 4 SATA 3.0 Devices does work on a ROG Strix X670E-E Gaming WiFi motherboard with CSM turned off and windows boot drive in a RAID.Windows 11 was able to see the drives attached to it and fully utilize them.The included SATA cables are pretty short, so I didn't use them, but would work if your drives are very close.Update: 4 months later and the card has stopped working. The lights flash briefly during boot, but then stay off and no longer light up. All drives connected to the card do not register anymore. Death was sudden; after a reboot attached drives were no longer connected. Debug difficult as documentation is sparse, other than general PC debug processes.Update2: Got a new card, a StarTech, and now finding out that all the the drives that were connected to the 10GTech card are bricked. They no longer spin up. All report "No Media Found" when connected via a SATA->USB card. So when 10Gtek died, it took everything with it. Now I'm replacing the card and 4 drives, very pricey solution when I was trying to save some money on a cheap pci-sata card.
Recommended Products
$34.99
$ 18 .99 $18.99