Your cart is empty.
Your cart is empty.Product Description
SparkyGLL
Reviewed in Germany on February 3, 2025
Diese Build Plates werden auf einem Ender 3 v3 KE verwendet.Haben damit zu Halloween Deko gedruckt und und über die Glitzereffekte gefreut.Modelle haften super auf den Oberflächen. Braucht bei uns keinen Kleber.Top. Empfehlenswert.
Gaetano
Reviewed in Italy on February 28, 2025
Ottimo piatto, sia dal lato liscio che dal lato strutturato, acquistato per una Sovol SV04 IDEX. Non copre completamente per pochi mm. l'intera superficie dell'heatbed [310x315 anziché 310x320) ma restano fuori giusto due striscioline marginali, che almeno nel mio caso risultano del tutto insignificanti per la stampa. D'altra parte è ormai molto difficile trovare un piatto a doppia faccia liscio/strutturato, dedicato per quella stampante.Stampo essenzialmente PETG e il piatto ha rivelato un'ottima superficie su entrambi i lati, con ottima adesione e rilascio immediato del pezzo a fine stampa. La superficie liscia è adattissima per pezzi che richiedono una finitura a specchio, che per me a volte è necessaria, mentre l'altra, che sembra anche piuttosto resistente, lascia sulla finitura di base, una texture non esageratamente ruvida.Buona trasmissione della temperatura, non rilevata strumentalmente ma la stampa tiene molto bene per tutta la durata, senza spostamenti accidentali. L'uso di colle e lacche non è più indispensabile: solo sulla superficie liscia, secondo me è consigliabile un velo sottile di adesivo che mantenga il pezzo fermo, altrimenti rischia di scivolare via, soprattutto con i movimenti di una IDEX come la SV04.Giudizio complessivamente più che positivo e, secondo me, prezzo congruo. Molto soddisfatto dell'acquisto.
denys h.
Reviewed in France on February 28, 2025
Super plaque lisse Ader nickel avec mon A1
Denesius
Reviewed in the United States on February 24, 2025
Nice plate, smooth on one side, textured on the other. Dimensions are good, and reasonably flat also.However.....it claims to fit the Ender 3 S1 Plus, but as you can see in the photo, the notches for the alignment pins are off. Didn't want to return, so ended up grinding the notches with a Dremel over to the right spot.On a new product
thomas hallahan
Reviewed in the United States on May 7, 2024
Short and sweet, I looked around for quite some time trying to find a solution to lifted prints on my artillery 3D printer. I spent a lot of time cleaning and trying various fixes from hours of research. Bought this slapped it on ran an auto level and never looked back. Hundreds of prints have been run and I don't even use a bed layer anymore. Well worth the price.
Daniel
Reviewed in the United States on May 18, 2024
Nice pattern on the PEY side but the PEI side doesn't have the best adhesion. I found my actual bed plate has a sag in the middle so leveling is difficult without the CR Touch. I go back to the glass bed for nice level prints
Stefan
Reviewed in the United Kingdom on December 24, 2024
Performs much better than BIQUs bambu platesGreat surface finish and works great at 40 degrees.Never had a single issue with adhesion even on a 10mm wide 250mm cylinder I tested it with in all 4 corners plus middle of build plate.Passed with flying colours and less than 13 punds delivered
Dru
Reviewed in Canada on January 4, 2024
I don't often leave actual reviews, but just had to after 2 weeks of using this build plate on my Bambu Lab X1C. This things just works time after time with such minimal maintenance.I was way too excited when it first arrived that I grabbed it and just put it in the printed and loaded up a print. Can anyone guess what happened based on that sentence? Print failed after first layers and started dragging print around the plate. Rookie move! I forgot to do 2 critical things. 1. I forgot to let it warm up. It came in the winter as this was December in Canada. It was cold. I should have preheated the build plate in the printer for about 10-15 minutes before first print. 2. Forgot to WASH IT! This is true of any plate you first open and are about to use. Wash it well with very warm water and dish soap that does not have additives that are meant to make your hands softer while doing dishes. Dawn works great, but I have issues with scents and Dawn has scented soap. I buy a cheap other brand that is clear and no smells added.After washing well and drying with paper towel and being sure to not touch the plate anywhere but the front and back "handle" like areas, I popped it in the printer and proceeded to print like a champ! Prints popped right off after leaving the plate to cool like 4-5 minutes after printing and a quick small bending of the plate. I can and have easily done 20 prints in between washes and even switching filaments. All i have to do it bend the plate, remove print, remove the 2 prep lines the printer always puts down and drop it back in the printer ready for the next print.Various filaments stick every time since my first hasty attempt.10/10 - would recommend and buy again if anything ever happens to this one.
A. Barajas
Reviewed in the United States on August 17, 2023
Bought this for my Artillery Sidewinder X1 and it fits perfectly. The X1 is notorious for having an imperfect build plate and this helped out a lot. Very easy to stick the magnet on and remove the PEI sheet. Definitely recommend.
Mario
Reviewed in the United States on April 23, 2023
Recently purchasing an Ender S1, I was struggling getting some of my prints off of the original plate. I didn't have an issue with the original pad and the first layer adhering, but I definitely had an issue with breaking a couple of my prints due to them refusing to release.I've made a couple prints since receiving my new UniTak3D Ender 3 PEI Printing Bed and every print has adhered great, and when it came time to release them from the plate they literally popped right off. Just taking the plate off the magnetic pad the first time, the print popped right off without me even having to do anything. Great upgrade, I'm very happy.
Collin Harris
Reviewed in the United States on December 15, 2022
After having a bunch of trouble with a smooth build plate with PETG I bought this and it works great. Paired with ABL it’s pretty much perfect and I haven’t had any issues with it holding onto prints or being difficult to remove them. I would recommend running a slightly thicker 1st layer or adding a slight z-offset in your slicer.
David J. Hauf
Reviewed in the United States on May 3, 2021
I had to recently design a part for a client and tried glass, but was not happy with the texture. Sure it was smooth and shiny, but showed way too many defects in the finally print. I was looking for a way to make a production part with a nice finish, so decided to try this steel bed with texture. I was extremely surprised at the results on my test print. I use this bed with PETG and it sticks extremely well. I use 85C bed temperature and gave it a quick wipe with isopropyl alcohol before I printed on it for the first time. You can see from the picture above that the texture is very nice and hides most of the surface lines from the 3d print. I definitely would recommend this to anyone looking to give their 3D prints that extra professional pop. I never had to remove the steal sheet to remove the prints when done printing, they popped off once the bed started to cool off very easily. If you do happen to get a stubborn print that you can't get off easy, it is convenient to be able to easily remove it since it's magnetic, and give it a quick flex to pop the prints right off. No scraping required. Overall I am very happy with this product.
Mark Byrd
Reviewed in the United States on April 4, 2021
I have been printing a lot of PETG recently and every once in awhile, separating a piece from the Ender/3 Pro's magnetic surface would actually separate some of that surface. Changing origins to avoid the remnant pothole works for awhile but eventually the potholes are everywhere. Critical print, no spare build surface EXCEPT this PEI sheet so necessity forced my hand.I installed the PEI sheet on the already installed magnetic mounting surface. I manually leveled the bed at all 4 corners using a doubled sheet of copy paper. I dial-in my bed level while the skirts are printing. I like using a large? 8" rectangle. For you? Save an hour... don't double the copy paper. Maybe even something thinner like vellum? Any how, for me, PETG would not stick until the nozzle was close, VERY close. And if you are not level there is going to be some undesirable contact with your new print surface. I had hoped to be able to switch surfaces depending on the material I was using but without automatic bed leveling, this would be a lot of recalibration.Mender/3 Pro's Mk8 hotend had been upgraded with a Capricorn PTFE tube and a .6mm nickel plated copper nozzle. At 240-245 degrees, PETG has been extruding .3 layers at 50mm/s just fine. Hotter than that and there will be clogs and other hot end failures. Faster than that and I get some under extrusion. Bed heat seemed to make little difference for 1st layer stick but 70 helped control a bit of lifting at corners; piece geometry and stuff like multi-layer skirts helped more.
Recommended Products