Your cart is empty.
Your cart is empty.
LCD/DLP Resin 3D Printer Magnetic Build Plate for Elegoo Saturn 3, Saturn 3, Saturn 2 and Saturn 8K
Installation Notes:
1.Please clean your build plate thoroughly, let it dry.
2.Please connect your magnet to the plate, let it sit for a couple of hours（More than 24 hours is better）so it is fully seated.
3.Please install the spring steel plate on the magnetic base
4.Please reset the printer's leveling settings to start printing
Skills in use:
1.When installing the soft magnetic sheet, it is necessary to ensure that the printing platform is clean and dry. After installation, it is best to keep it in an inverted state, or it can be fixed with a clamp to ensure that the soft magnetic sheet is fully attached to the printing platform.
2.Please ensure spring steel is completely aligned with the magnetic base to avoid the resin entering the gap during use, which will affect the magnetic force of the soft magnet and cause the spring steel plate to fall off.
3.If there are burrs on the surface of the spring steel, please use sandpaper carefully to make sure that there are no burrs before using it to prevent the burrs on the spring steel from piercing the FEP film during the printing process.
4.After printing, do not excessively bend the spring steel when removing the model. After use, use alcohol or cleaning fluid to remove the residual resin on the surface.
5.After using for a period of time, if the model falls off the spring steel sheet during the printing process, you can sand the spring steel sheet with sandpaper to ensure that it has sufficient adhesion.
Package includes: 1PC spring steel build plate+ 1PC soft magnetic sheet
The Gambles
Reviewed in the United States on January 3, 2025
Work like they should.
Kenneth R.
Reviewed in the United States on January 26, 2025
Works great and cheaper than some other options. Clean build plate, stick it on and let it sit over night.
Amadeus
Reviewed in the United States on September 17, 2024
These are good magnet plates for resin printing. I sanded the surface a little rougher to give a little more adhesion. The problem with them is that the adhesive on the magnet is sensitive to the resin. It starts to dissolve around the edges in sometimes as little as two months, but I've had it last seven months also. Always prepped with a good cleaning and alcohol wipe down of the plate before applying. The latest thing I am doing is running a bead of silicone RTV around the edge of the magnet where it's stuck to the bed to keep the resin out of contact with the adhesive. Three months so far and no sign of the edges pulling loose but it's still early so ......
Alberto
Reviewed in Spain on August 25, 2024
Funciona de lujo. (MUY IMPORTANTE ) Limpiar bien la base antes de pegar el iman.
P. Bonifaci
Reviewed in the United States on May 6, 2024
The plate itself works well on my printer. But after about six months of use the magnet/glue failed and peeled off the build plate.
giel bloks
Reviewed in the Netherlands on November 21, 2024
Past precies op mijn printer magneet is veelsterker dan op andere producten die ik heb.Een volle buildplate printen is geen probleem!Hechting vd zelfklevende laag is ook goed
Ranperre
Reviewed in the United States on October 19, 2024
Perfect fit for the mars 3 pro. The magnet is plenty strong enough and the plate can peel off easily and of course it makes the print removal extra easy
Danii
Reviewed in Sweden on April 24, 2024
Perfekt att bara kunna lossa magnetplattan efter utskrift. Och en lätt böjning så släpper utskriften!
gloria f
Reviewed in Mexico on September 13, 2023
Buen producto, instrucciones simples y fáciles de seguir. Mi único pero es la pestaña para despegar la placa del imán, es un poco pequeña y difícil de tomar con guantes, también puede cortarlos, a pesar de eso funciona bien, la adherencia hasta el momento va bien. Lo recomiendo
Kalebh
Reviewed in the United States on July 22, 2023
I suppose they use different mm measurements in China or wherever this came from. This plainly didn't fit the elegoo Saturn S like the measurements would imply. This WOULD fit the original Saturn but not this one.UPDATE:This magnetic plate sorta works... It is actually so strong that it wants to stick to the bottom of the vat which jostles the builds plate and ruins prints AND the FEP film AND the LCD screen... That, or, the stainless steel plate just doesn't have decent adhesion. I did 70sec at 60um and it didn't stick... dozens of different settings...Wtf? This stopped working on even small prints and ended up really screwing up my printer.This is cheap sheet metal off the street with a huge, over active (and not very sticky) magnet
Labowski (Dude)
Reviewed in the United States on November 4, 2022
Determined the issue was with properly setting my home and also setting my Z offset. Also, taking sandpaper to the build plate helped the prints stick to it. As a novice printer, I'm learning as I go. Utilizing the cones of calibration tool helped tremendously. I have a Saturn S, and I had to adjust/tweak my settings to get optimal builds and reduce failures. My adjusted settings are as follows:- Base bottom layer count was 5 layers, changed to 4 layers- Base bottom exposure was 30 seconds, changed to 20 seconds- Base Exposure time was 2.5 seconds, changed to 3.0 seconds.**One key note regarding calibration: When homing my build plate, I now use my vat and I level/home/Z offset my build plate to my vat. I add resin to my vat so that it's about 1/4th full, loosen the build plate bolts, and then home it with the resin in the vat. This is alleviating the prints sticking to the FEP.The cones of calibration takes an hour to print but uses minimal resin and will save time (in the long run) alleviating the headaches/frustrations of getting failed prints.Hope this helps, and remember, with 3D printing, slow is smooth, smooth is fast. Fast and bad is 'bad' and is a waste of money, time, and resin. All the best.------------------------------------------------------------------Executed 6 prints. All failed. Tried googling/youtub'ing walk throughs, setting adjustments, etc. with each failure to accommodate the magnetic build plate in hopes of a successful print. All prints failed. Every print stuck to the FEP. Additionally, to make sure it wasn't due to the FEP, I replaced the FEP. Prints still went to the FEP and would not take on the magnetic build plate. I will be returning these. Save your money. These are a dud. Hope this helps someone and all of the best.
D. Dehner
Reviewed in the United States on November 20, 2022
Surprised at how nice these are for the money - and they really work. The flexibility is really nice on these and your models pop right off.The first layer burn on these has been amazing - meaning the stickiness to hold and create a good first few layers to hold the model. Others have been too smooth and don't adhere the model and you end up either dropping in the resin or failing to launch entirely.This is my 3rd set of these I've purchased the first set from another company - could get adhesion, second same, third try is the WIN. Tried the other set again just to make sure I wasn't crazy - nope could start the model. Put these suckers back in place - BOOM! First time always.Pros:- Crazy first layer adhesion - no drops or bad starts- Flexible- Pops models of great- No sharp edges
Recommended Products
