Your cart is empty.
Your cart is empty.TEMO 1/32 Inch Diameter Carbide Downcut Inlay Router Bit CNC End Mill 1/8 Inch Shank, Ideal for Wood Carving, Slot Mortise, Engraving, Grinding
Customer
Reviewed in the United States on January 30, 2025
They are solid, they are long.That being said , it can be good thing or bad thing . They are down cut router bits , I used the 3/32nd , and the 1/8th inch bits fine. But The 1/16th and 3/64th snapped immediately while I was trying to cut pockets for pearl inlay on a guitar headstock. The bigger down cut bits, work very well cutting bridge slots, but you have to make small cuts ( they are down cut) . But they leave a smooth bottom finish for the bone saddle to rest.
yawnny
Reviewed in the United States on January 16, 2025
i needed to do some minor inlay work on a vintage guitar, to replace a headstock logo.The bit I used, worked flawlessly, and the repair came off better than I had expected, dueto my inexperience with inlay work.Seeing how expensive these type of bits can get, I feel these worked just fine, and will hopefullyuse them more in the future.
BB
Reviewed in the United States on January 12, 2025
These router bits are absolutely unsuitable for their intended purpose. I purchased two bits. Both broke the instant the touched wood. The pictures tell the story. How could a company think they could sell these bits and people wouldn't notice they are a scam? I just wanted to save others from wasting their time.
PBrady
Reviewed in the United States on May 17, 2024
I use this size bit for my dremel to help me with detail inlay work on guitars. cuts well, good price also
Uknowdakine
Reviewed in the United States on January 16, 2024
Used this bit as a detail bit for a 5 hour carve on my cnc router. I slow every motion down to ensure they bit wasn't stressed. 4.5 hours into the carve it snapped
Gerald Freese
Reviewed in the United States on April 14, 2024
Can't beat them for the price and work like they're supposed to...
Scott Oliver
Reviewed in the United States on June 18, 2021
Used it for some 5mm depth detail work around small lettering in tigerwood. I bought this bit simply to experiment with and based on how thin it is I was expecting to break it immediately. I was very conservative on speeds and feeds on my Shapeoko CNC, and successfully completed my first job. A useful bit added to my collection!
Kindle Customer
Reviewed in Australia on February 25, 2021
I’ll be using these to do inlays in guitar fretboards. Did a quick test and they cut as expected.
Ryan
Reviewed in Canada on February 18, 2021
Product came pre broken. I'm hesitant to even use them if they broke on the way here.
Jalp
Reviewed in Canada on July 2, 2020
I’ve been using this bit for a while now! Engraved on walnut, pine, cut through mdf a few times. It’s lasting really well and I’ll buy it again when it wears out or breaks.
Spectel
Reviewed in Canada on February 3, 2020
To date I used the 3/64” bit in my Dremel rotary tool for inlaying copper wire into wooden boxes and the downcut flutes left a relatively clean cut. I will have to determine where to use the other sizes. I wish I had the option to substitute the other sizes in the package price. I would have ordered more of the 3/64 size knowing it’s the one I will use the most in the near future.
M. Redmond
Reviewed in the United States on October 13, 2020
I used the 1/16" downcut bits to cut mahogany and maple. The attached pictures show the mahogany, all of which was cut with the 1/16" bit. The maple was largely cut with a 1/8" bit from a different maker, but the small holes in its center were cut with this 1/16" bit.I couldn't be happier with the results. No tearout or chipping at all. I ran the bit at 18,000 RPM and 36 IPM.
ron biersteker
Reviewed in Canada on January 2, 2020
Worked as it should. Nice clean cuts in Black Walnut. Used in Shaper Origin handheld CNC router.
Recommended Products
