Your cart is empty.
Your cart is empty. Thickness: 3.0mm Dimension:400x400mm
Color:Black
Material: Fiber Glass
FR-4 is a thermoseting industrial laminate consisting of a continuous filament glass.Cloth material with an epoxy resin binder. It has characteristics of high strength. It has excellent electrical properties and chemical resistance.
Application:Widely used in RC model , 3D print bed, control surface horns, servo trays, autogyro rotor plates and many general strengthening parts. For DIY handle
R.Y
Reviewed in the United States on January 15, 2025
Had high hopes for this but ended up going back to a glass bed. For pla it’s fine but for large Asa the parts just didn’t stick well enough.
Lexx
Reviewed in Canada on August 21, 2024
See pics. I tried 3, all have these surface defects that do transfer to the print. One of the 3 was just scratched up. Vendor asserts this is rare, but clearly it’s 100%, not at all rare.Returning 2, keeping 1 because it’s already attached to a magnetic plate that I don’t intend to further destroy.
Micheal
Reviewed in the United States on July 4, 2024
Highly recommend this for pla. Petg was difficult but works great after cleaning with alcohol.
RM
Reviewed in the United States on May 5, 2024
Please note, that I received exactly what I purchased as described, well packaged and shipped to me without complaint. I only give this four stars because I bought this in hope it would be better than the pei plate that I am currently using, It works ok for PLA, things stick but it's not better than what I already have.
shunquan shen
Reviewed in the United States on May 2, 2024
I've used this on pla and petg, and it has preformed very well, better than the pei sheet I had before. Great product, deserves the 5 stars
Justin Murphy
Reviewed in the United States on February 14, 2024
Do not set your z offset too low. It will be really difficult to remove to a point where you need a plastic scraper to remove the residue. Other than that my prints with polycarbonate stick to the g10 really well.
Ribon
Reviewed in the United States on October 4, 2024
Great surface that sticks to everything I tried, just use some glue and it can be used for multiple prints. Used transfer adhesive to glue it to a bad and resurfaced bedplate for my Kobra 3.
Donovan
Reviewed in the United States on October 17, 2024
This is how mine arrived. At first, I thought it might just be a plastic film on top that got scuffed. However, there is an absolutely staggering amount of scratches on both sides of the G10 itself. This is what happens when the manufacturer doesn't protect the surface during production and processes the material on top of debris-filled work surfaces. It's not obvious with my lighting, but there are also stain-like patterns on both surfaces. I doubt that affects its properties as a print surface but there's no way I would print on this anyway because I don't want a million ugly scratches transferring to everything I make.
Coop
Reviewed in the United States on January 30, 2024
This is an outrageously high-performance print surface overall, and will last a very long time if you treat it properly.The main selling point for this surface is that it performs well on PLA, ABS, and PETG (and possibly more) without ANY bed preparation, glue stick, etc.PLA sticks like glue at 55C. For a surface this smooth, it has unusually good adhesion. PETG sticks nearly as well at 75C, and adhesion can be improved by slowing the initial layer. ABS is a bit more demanding, but with a slow initial layer, and a high bed temp (100C works well for me), you can print reliably. ABS still occasionally shows signs of lifting in the corners of prints, but it has never caused a print failure.All of these materials will self-release once they have cooled. You MUST WAIT for this to happen, or you will damage the print surface by yanking on your parts.This is a fairly soft surface, and can be scratched and damaged easily. Do not use a scraper on this bed. Do not allow your printers nozzle to drag along this bed. They will permanently damage it. I recommend cleaning it with isopropyl alcohol and a clean rag.This specific sheet (235x235) is perfectly sized for an Ender 3 or K1. The edges are a bit rough, the corners are a bit sharp, but the sizing is perfect.I have bought a few of these, and I find that usually only one of the two sides is perfectly smooth. One side usually has some scuffs in it.
Recommended Products
