Your cart is empty.
Your cart is empty.4.6 out of 5 stars
- #45 in Heatsinks
This set of raspberry pi 4 heatsink kit, includes 15pcs anodized black aluminum + 5pcs copper cooling heat sink. These pure aluminum (15 pcs) and copper (5pcs) heatsink include heat conductive adhesive tape for optimum thermal transfer. These heat sinks have profiles which are short enough to fit within standard Raspberry Pi cases. These heat sinks kit can be applied in other devices to cool processor, regulators, VRM VRAM VGA RAM, small IC Chips, MOSFET SCR, Southbridge, Northbridge M.2 PS5 etc. Package includes: 5pcs aluminum large heatsink: 0.56 x 0.56 x 0.27 inch (14mm x 14mm x 7mm) (L*W*H); 5pcs aluminum small heatsink: 0.35 x 0.35 x 0.19 inch (8.8mm x 8.8mm x 5mm) (L*W*H); 5pcs aluminum heatsink 0.56 x 0.39 x 0.27 inch (14mm x 10mm x 7mm); 5pcs copper pad shim heat sink: 0.59 x 0.59 x 0.02 inch (15mm x 15mm x 0.5mm) (L*W*H).
Carter
Reviewed in the United States on January 3, 2025
I put these little heat sinks inside a projector on the bulb housing to help dissipate some of the heat. I replaced the projector fan with a slightly less powerful and quieter fan and wanted to make sure the heat would still be removed. These sinks attached easily and definitely won't come off without a fight.
Cubes Codes+
Reviewed in the United States on June 6, 2024
I used this on my raspberry pi 4 and the extra on my Pi zero. They are in a cluster together so it is important they both stay cool. Reduced temperatures down by over 10 degrees celsius!
3Dprinter person 258
Reviewed in the United States on June 16, 2024
Easy to install fits pi 4.
Richard W. Koscierzynski
Reviewed in the United States on May 5, 2024
I bought a ov5640 5MG camera for a EPS32-CAM and the images were looking pink because of the camera getting hot. I put one of the copper heatsinks on the camera and now the images are GREAT!
takatti
Reviewed in Japan on May 1, 2024
dmonitorの挙動がおかしかったので熱の影響があるかなと疑って購入しました。特に関係無かったです。しかし部品の機能としては十分だと思います。
Brad Sinclair
Reviewed in the United States on November 28, 2024
great product for less$$
Seasons
Reviewed in the United States on February 11, 2023
Cheap, fits nicely, comes with an added copper plate for the bottom of the pi. This is not a necessary product if you do not need to run intense processes on your pi, however if you do, buying this + a fan-case is an absolute necessity even for hobbyists.Keep in mind that the adhesion is good enough to prevent the heatsinks from coming off when brushing against them, however they are still easy to remove. This may not be desirable for someone looking for a more permanent solution to heatsinks.
Martijn Pollmann
Reviewed in the Netherlands on March 13, 2022
Does nothing for the temperature of the Pi.
Carlos
Reviewed in Spain on November 23, 2022
Funciona maravillosamente para mi raspberry pi 4 (aunque la placa lisa sobra, al poder ponerse solo en la raspberry pi 3).Es una solución sencilla y barata que mejora mucho las temperaturas de forma pasiva. Y si encima de eso le pones un pequeño ventilador, los resultados son excelentes.
javier
Reviewed in Spain on April 14, 2021
Comprados para mi raspberry 4 y decir que por el precio que tiene, merecen la pena. El adhesivo que traen se pega correctamente y realizan su funcion como deben. De hecho uso mi Pi sin ventilador de ningun tipo.
Stevil
Reviewed in the United States on July 13, 2020
I noticed that there was a chip on the underside of my Raspberry Pi 3B+ that runs very hot, and I suspected that the Pi was throttling back due to excessive heat. I didn't think I had enough clearance under the board for the finned heatsink (I probably did though,) so I used the flat copper heat spreader. It did the trick- the hot spot is much more diffuse and runs much cooler (verified with a digital thermometer.) I also used the finned heat sink on the main processor. No evidence of heat-related throttling any more.
Ken Hoang
Reviewed in the United Kingdom on November 11, 2020
Easy to use heatsink not only for raspberry pi but other electrical component. I used it to cool a mosfet that power an LED strip
Adam
Reviewed in the United States on December 20, 2017
I purchased this for an off-label use and it's working well so far. I've got an NVIDIA 550ti card that I've been trying to squeeze life out of since I bought it on sale a couple of years ago. It was running at 70-72c at max settings on what it's used for. After sticking all these bits, aside from one copper plate, to the backside of all the chips, it's consistently running at 69c under the same conditions. For $8.00 shipped (Prime), I'm pleased with this purchase. I actually found a place to use the 5th copper plate, but it involves unsticking one of the large sinks. I'm not sure how well the adhesive will work with repositioning. I'll post an update if I do that.
Recommended Products
