Your cart is empty.
Your cart is empty.Product Description
Stainless Steel Horizontal Centrifugal Pump & Motor
- Reliable single stage or multistage impeller designs
- All stainless steel wet end construction for reliability
- Able to pump hot water up to 158°F
- Carbon/Ceramic mechanical seal for reliable operation
- Higher than normal 120°F ambient temperature rating
- High operating temperature and high current draw protection
- Robust TEFC motor constructed from corrosion resistant materials
- IP55 international protection rating for dust and dirt
- Permanently split capacitor for reliable starting
- Motor and pump are designed for frequent starts
Torrium 2 Controller
- Larger water pathway provides superior hydraulic performance
- Adaptive starting - monitors incoming pressure
- Quick cut-in for constant flow and even water pressure
- Extra Draw off Capacity w/ Built In Accumulator
- Easy status check LED's
- Dry run protection with auto restart
- High Water Temp, Excessive Electrical Current and Power Surge Protection
- Corrosion & Scale Resistance
- Vertical/horizontal 360° discharge
- Power Cable - 6 ft power cord with standard NEMA power plug
Choose from five different models with varying performance curves for most any application.
Hydraulic Performance is the amount of pressure boost the pump will add to your incoming pressure at a specific flow rate. Select the best pump for your application based upon your existing incoming pressure and desired combined system pressure (Usually < 80 psi to meet local building codes.) Model / Voltage / Incoming Pressure Range
- BT14-30 / 120V / 22-60 psi Incoming Pressure
- BT14-45 / 120V / 2-40 psi Incoming Pressure
- BT20-30 / 120V / 10-50 psi Incoming Pressure
- BT20-40 / 240V / 0-20 psi Incoming Pressure
- BT30-30 / 240V / 10-50 psi Incoming Pressure
Note: Do not exceed a Maximum System Pressure of 100 psi (incoming pressure PLUS pump boost).
Kimberly Adkins
Reviewed in the United States on July 2, 2024
Pumped water fine. Control module on top is supposed alleviate need for pressure switch. Not effective. Missed my return window. Home Depot pump working fine as replacent.
Jason Stone
Reviewed in the United States on March 14, 2024
I used this as a booster pump to take very low city water pressure up to 70psi. I installed a pressure regulator before the pump to make the pump get 30psi going in to pump intake. Which made my output pressure out about 70 which was perfect for residential home.
Gillman
Reviewed in the United States on October 27, 2024
Wish this had a little more boost, but still a worthy investment.
christopher
Reviewed in the United States on October 23, 2022
Great pump! Definitely recommend.
Wayne
Reviewed in the United States on June 14, 2021
Very easy to install but as other reviews have claimed, make sure you use copious amounts of quality thread tape. The manufacturer specifies no dope can be used, only tape. I thought I used enough the first time (about 6 or 7 layers) but it leaked. I went nutty and wrapped it almost 20 times and haven't had an issue since.This pump is extremely quiet. It creates even less noise than my AC or heat. I mounted mine to a piece of 1x4 cca and used rubber furniture pucks also to dampen any vibration noise. In retrospect, I probably didn't need any of that.The pump I chose only puts out a consistent 38 psi. My main line was putting out anywhere between 40 and 45 psi. You definitely need to install a regulator. I set mine at a consistent 72 psi and everything works well now.
Ryan R Bickford
Reviewed in the United States on April 8, 2020
This looks like a nice little pump, and definitely more suited to my household needs for constant water pressure. I’m in the process of installing it now. (These are the positives so far).The negative is that for some reason Primo pumps thought I wouldn’t notice that they sent me an open box pump! It’s missing install instructions, as well as the controller wrench. I’m seriously hoping it works when I plug it in!!
Ranger
Reviewed in the United States on September 28, 2019
I am using this as a booster pump for water coming into the house. Incoming pressure is about 35 psig. The pump raises the pressure to about 70 psig.Installed the pump in the basement. It has been working flawlessly since installed. It cuts on automatically based on pressure. Instructions / information provided with the pump were excellent.
Randy V.
Reviewed in the United States on January 16, 2015
I installed this to replace a broken booster pump to increase water pressure between the city water supply and my townhouse. I had a pressure control valve installed between the pump and the house to make sure the pressure isn't raised too high. The old pump did not have this set up and it would take the skin off the top of your head in the shower. The new pump works great. I researched several pumps before selecting this one. This pump has the best service record compared to the other pumps I researched.
Recommended Products
$1,127.00
$ 99 .00 $99.00