Your cart is empty.
Your cart is empty.Product Description
Beduan, manufacturer & distributor of top pneumatic supplies Our production line includes:
- Compressor Filter and Regulator
- Push to Connect Fittings
- Solenoid Valve
- Compressed Ferrule Fitting
- Marginal product
- Search Beduan and choose what you want
Beduan 2 Way Electric Solenoid Air Valve
Normally Closed Electric Solenoid
Body Material : Anodized Aluminum
Pressure Range: 115 PSI.
Size：1/4” | 1/8“
Position & Way Number : Two-position,Two-way.
2-way normally closed solenoid valve is to control On/Off of air and inert gas. This solenoid valve has one 1/4" inch NPT inlet and one 1/4" inch NPT outlet port. Valve stays close when the coil is de-energized- and it opens when energized. Has two holes in the bottom and can be mounted in any position.
Solenoid Valve Installation Instructions
- Clean and rinse the impurities in the pipeline before installation;The thread should be wound with Teflon Tape. Be careful not to drop the debris into the pipeline to prevent blocking the solenoid valve.
- When installing, keep the arrow direction on the valve body consistent with the flow direction of the medium;If there is reverse pressure, a check valve shall be installed.
- In order to ensure and extend the service life of the solenoid valve, the installation should be horizontal, the coil is vertical up, not vertical or backward installation.
- After the solenoid valve coil outlet wire (connector) is connected, it should be confirmed that whether the contact of electrical components should be firmly connected should not shake, looseness will cause the solenoid valve not to work.
- Solenoid valves that are out of service for a long time should be cleaned of impurity condensation before use.
- Solenoid valves are not suitable for fluids under the following conditions: A.Changing into a liquid by heating and into a solid by cooling; B.Viscosity greater than CST50.
Karmon keesee
Reviewed in the United States on March 7, 2025
This little thing BLEW my mind away
Scott1978
Reviewed in the United States on February 25, 2025
This thing was crazy loud the moment I plugged it in. Much louder than the air pump for my aquarium. I wouldn't even consider using this, it would be like adding a loud erratic buzzing sound to your life. I'm amazed I don't see a lot of people complaining about it, it may be that mine is defective, but I wouldn't try again.
diego
Reviewed in Mexico on January 30, 2025
cumplio con las expectativas
Great product
Reviewed in the United States on September 30, 2024
I have ordered 3 now 1st worked so well that I ordered a 2nd the 2nd has a defected seal so I got another not worth the time and trouble over returning for 10 dollars.
Leland E Wilson
Reviewed in the United States on August 13, 2024
I am using this to control an air horn and it works great. I expected a delay from the time I tap the horn button for the horn to blast but this is instant! I am running it at around 120 psi and it has been flawless so far. I am surprised at just how well it works given the price.
Customer
Reviewed in Australia on March 31, 2024
does the laser air supply great
mitch
Reviewed in the United States on February 9, 2024
The media could not be loaded.
Yeah
Reviewed in the United States on December 21, 2024
Look good
Tyler C.
Reviewed in the United States on December 20, 2024
I bought this for my CO2 Laser. It allowed me to control the air flow from the electronic board. Before installing the air would be constantly on! This product same in well packaged and has worked as intended! Would recommend!
Joe J.
Reviewed in the United States on December 17, 2024
The media could not be loaded.
Sundesh Balraj
Reviewed in Canada on March 14, 2022
Hooked this between my compressor and my laser engraver to control the air flow to the nozzle - worked first time and simple to intstall the wiring. Works like a charm.
Manuel soto
Reviewed in Mexico on February 11, 2022
Lo vuelvo a comprar
Alex Côté
Reviewed in Canada on November 7, 2020
Il as fonctionné 5 secondes
Recommended Products