Your cart is empty.
Your cart is empty.The Yonico 14520 5 bit Dovetail router bit set contains 5 Common Dovetail Bit sizes and angles needed for most dovetail projects. Can be used with a dovetail jig for half-blind Dovetail joints or can be used together with dado bits to produce through-dovetail joints.
Reno
Reviewed in the United States on February 9, 2025
Was able to get the right router bit for half of what I was expecting to pay. Came quickly and works great!
Dennis T Pymm
Reviewed in the United States on February 22, 2025
as advertised
Jeff Vallender
Reviewed in the United States on January 24, 2025
Good quality
PDS
Reviewed in the United States on January 17, 2025
I will rarely use a dovetail joint, and these bits from other sources can be quite expensive. But I needed a bit to cut dovetails on pieces of track for a toy train I am building for grandson. This bit did the job well, cut cleanly, and I am very pleased with it, as it didn't "break the bank" too!
Alpha Coyote
Reviewed in the United States on June 27, 2024
I have only used this cutter to make one box so far, but on first impressions it's great. The cutter head is solid carbide, brazed onto a steel shank. The dovetail has a nice slim profile that matches many hand-cut dovetails I've seen. I did experience a little but of tear out, but I don't think I can blame the bit for that. Will try with a backer board on both sides of the work next time.
E Lewis
Reviewed in the United States on December 27, 2024
Bought to use with dovetail jig. Cuts well and inexpensive.
Glenn Smith
Reviewed in the United States on January 11, 2024
I own a small Festool trim router. The Collet size is 1/4". My Porter Cable dovetail jig system 4212 requires a special size router bit. The bit that comes with the jig has a 1/2" shaft. It will not allow me to use the 1/4" collet. There is no mini router that offers a 1/2" collet.The angle of the cutting edges is critical to produce properly fitting dovetails. This is not a common size bit. This bit meets the requirements. The length of the cutting edges is also important. This bit provides the length needed.The carbide cutters are very sharp. The bit is balanced and does not vibrate when used in my Festool router. When cutting dovetails in plywood, the glues used are very abrasive to any bit and build up a thin coating on the edges. This results in smoking and burning of the wood. I use a lot of Baltic Birch plywood and this is hard on bits.Thus far this bit cuts the same as more expensive bits usually available from local woodworking stores. I expect given these results that the life of the bit will be about the same as more expensive bits, sometimes costing 2x to 3x as much. The cost of these bits is very attractive when it comes time to replace one.You should be able to use this bit for a very long time in ordinary hardwoods ie. Oak, Walnut, Birch, Poplar and my favorite - Cherry. You can expect the same fuzzy cuts in Poplar or other softer hardwood. It will require the use of a sharp chisel, razor knife or sandpaper to remove the fuzz.I have several routers but prefer to use the Festool for dovetails and edge trimming of laminates and veneers. The reason for this is the ability to accurately adjust the depth of cut 1/256" per click of the adjusting knob. I used to use a Porter Cable mini router for this but it was very difficult to adjust and lock the depth of cut in place.This router bit makes a clean cut at the bottom of the dovetail. It is easy to make a professional furniture grade joint. At local Big Box and Specialty Stores finding a 17/32" dia bit is similar to seeking the Holy Grail. Even Monty Python couldn't find it. Next time you want to replace your dovetail bit - Amazon and Acme tools will have it to you within 2 days. Mine came the next day.The only negative thing I can add is that now I have to build another wood box for my Porter Cable Jig and Accessory box to make room for this bit. Wait! I like to build boxes. Maybe this is a positive. Good product, great price and you should buy this.
David Thompson
Reviewed in the United States on April 1, 2024
Needed 14 degree 1/2" bit with 1/4" shaft. This seems to fit the bill. Haven't tried with microjig set yet. Will update.
sixtieswarbler
Reviewed in the United Kingdom on May 5, 2022
Happy with the tool at a reasonable cost.
Colin
Reviewed in Canada on April 18, 2021
As others have said, very stiff to remove from grommets in the box. I used a pair of pliers to get them out. I drilled a 1/4" bit into the plastic bit holders and they come out a lot better now. Good variety I have only used the largest bit on my CNC and made a clean cut in Fir 2x4.
cristiano
Reviewed in Italy on November 19, 2020
Buon prodotto
Cliente de
Reviewed in Mexico on February 27, 2018
Realizan muy bien su trabajo, excelente calidad, se nota que se utilizan materiales de alta calidad dn su construccion, recomendables
Alain Dubé
Reviewed in Canada on February 20, 2018
Belle qualité et bon prix.
Recommended Products
$84.58
$ 34 .99 $34.99
$14.99
$ 7 .99 $7.99
$41.95
$ 22 .99 $22.99