Your cart is empty.
Your cart is empty.
Yakamoz 2pcs 1/4-Inch Shank Panel Top & Bottom Bearing Flush Trim Pattern Router Bit Set with Replacement Bearings
Features:
Cutter: Carbide Tipped
Hook & Shear Angles: High hook & shear angles allow cutters to slice smoothly into stock producing clean, splinter free.
Bearing: Totally enclosed & lubricated
Coating: Baked on heat resistant coating prevents build-up of sawdust, resin, and pitch.
Balance:+/- .003" tolerance (allowing smooth operation at high RPMs)
Specification:
Body: Solid Hardened Steel
Blade: Industrial Grade Micro Grain Carbide
Shank: 1/4"
Overall Length: 3-2/5"
Blade Height: 1-1/2"
Bearing Diameter: 1/2''
Replacement Bearings Quantity: 10Pcs with screws and wrench
Application:
Be used with either a top or bottom template. Especially useful for template work when routing rounded or curvy wood with sensitive end-grains.
Package Included:
2 x Flush Trim Router Bits
1 x 10Pcs Top Replacment Bearings Set
stefano
Reviewed in the United States on September 9, 2024
The bits are working as expected
Patch craft
Reviewed in Australia on August 8, 2024
These items were as advertised
Joey Sutherland
Reviewed in the United States on March 1, 2024
The media could not be loaded.
Ninti Blue
Reviewed in Australia on October 9, 2024
With a bearing on each end, trimming is so much easier. The ~50mm cutting lengths of the bit has proved very handy on bench top trims.
ersted
Reviewed in the United States on October 29, 2024
Well made and durable product with one caution. Fine print in the instructions state, but does not emphasize, that they should not be run at > 10,000 rpm. This is critical. Run them too fast, they can self destruct. Got exciting.
todd messick
Reviewed in the United States on October 22, 2024
Liked extra bearings for pattern trimming. Good price
Michael Pickering
Reviewed in the United States on April 10, 2024
The flush bit did what it was supposed. Worked great.
Neil Covington
Reviewed in the United States on June 15, 2023
Not super expensive so I can’t complain. Out of the box they are about as sharp as a name brand bit halfway through it’s useful life. Make sure to add some removable thread locker to The set screw on the bearing retention ring or it will go flying in a few minutes. I would recommend these to someone that doesn’t need top quality and doesn’t use them very often. The price matches the quality.
Sergio Basulto Corona
Reviewed in Mexico on May 4, 2023
Derek Moore
Reviewed in Australia on July 27, 2022
So far so good
trevor leffler
Reviewed in Australia on November 4, 2022
clean finish
phil
Reviewed in the United States on May 4, 2021
this is a cheapo. so go slow and chew less meat.best to run a variable speed controller and run it at medium speed.if you fail to listen to this then u get what you get.dont be stew peddcheerzp.s. i would buy again if i blow this one up
DanF
Reviewed in the United States on October 19, 2021
I was worried because other flush trim bits this long with 1/4" shafts have had bad reviews, and most of the big names don't make them this long - probably because the force applied at that length can really damage a shaft. These bits had no problems. I used them in a Ridgid compact cordless router to trim the bullnoses off thirteen 1 1/2" thick yellow pine stair treads. It was a little slow going but the bit handled it perfectly and is still going strong. Will definitely look for this brand again. Oh - and it was sharp and much less expensive than those big name brands.
Recommended Products
$35.85
$ 16 .99 $16.99
$31.95
$ 15 .99 $15.99