Your cart is empty.
Your cart is empty.Worbla's Finest Art (aka Original) 8x8 inch sheet - Perfect for Small Projects, Bracelets, and Trim - Thermoplastic- Worbla's Finest Art (Original) : Incredibly easy to use with an activation temperature of 90°C, Worbla becomes soft and pliable, allowing you to shape, form and mold the product by hand safely. The adhesive properties mean pieces can be joined without the need for glue, and scraps can be blended for zero waste. These leftovers can be molded to act just like putty, and many artists use Worbla’s Finest Art instead of clay to create near-indestructible pieces. Non-Toxic and Skin-Safe, Worbla’s Finest Art can be used in classrooms, apartments, workshops and beyond without needing uncomfortable safety gear or complicated venting systems. Use hot air such as a heat gun, water or steam to shape the plastic however you want.
C.C
Reviewed in the United States on September 10, 2024
I cannot get this sticker off! I've scraped and pulled and used a blade even to try to pry it from the slick side! It's like welded to it. Very frustrating. I can't use googon cause I don't want to mix anti stickiness into the glue holding this together. Why would you put this sticker on this side in the first place?? Why not have it on the packaging? Why not have it on the rough side so it's easier to remove?? Very annoying that I have a piece I cannot use.
Kersleaf
Reviewed in the United States on July 27, 2024
I used this to make a base for a pony tail wig for a con and it was perfect. Very easy to use and mold
Hair Goddess
Reviewed in the United States on March 21, 2024
Used for a costume project. Only thing can complain about is that you don't get a whole lot for your buck.
DJ
Reviewed in the United States on March 13, 2024
It's worbla, cosplayers swear by the stuff for a reason, it works great.My gripe is that the sticker is stuck directly on the product and doesn't come off. First picture I tried nails and x-acto knife and got nowhere. I had to heat it up to get it off, and even then I couldn't get all of it. So now I have this sticky, mangled piece of worbla. Like it works fine for what I'm using for, but I'm a little peeved that it costs an arm and a leg for one, screwed up sheet.If I could do 3.5, I would. 3 is too low because it still works, but 4 feels too high for this issue
Alexandria Shaw
Reviewed in the United States on October 2, 2024
Smaller than I thought but hopefully I can make what I need to with this amount of it for a cosplay I’m doing. I’ll update with pictures
Meow cat
Reviewed in the United States on June 3, 2022
I had a individual project to mechanically test materials. I sourced several thermoplastics and Finest Art performed really well. It was easier to use and form into needed shapes. Their customer service is fast and responsive.I wouldn’t use another type of thermoplastic and will most likely only use Worbla products in future projects.
Etta B.
Reviewed in the United States on June 3, 2021
My rating of two stars applies only to the packing presentation, not the product itself. The sheet arrived at the bottom of a shipping box with another item. It was not wrapped in any way. Just the bare sheet, not cut particularly square, with a barcode label stuck on it. But the problem was that there was no instruction sheet at all. Not how to cut, how long to heat, whether to boil it, use a hair dryer, or a heat gun. As a newcomer to the material, I guess I am expected to figure out how to use it myself via google, but it sure would have been nice to have some direction.
Raquel
Reviewed in the United States on June 26, 2018
Don't buy tooo expensive and not even 1/8 of a sheet
Recommended Products
$19.97
$ 8 .99 $8.99