Your cart is empty.
Your cart is empty.Product Description
Upgraded Fuel Injector Tester and Cleaning Adapters Kit Oil Injector Diagnosis Tool DIY Cleaning Tool Kit
This tester can help diagnose injector problems, and you can use it to test each injector individually to help identify stuck, leaking, or burnout conditions.
It has four pulse modes, the user can choose a suitable mode according to the test needs, and the continuous mode (mode 4) helps to identify the good or bad of the injector.
Two fuel injector adapters, one large and one small, are compatible with most fuel injector models.
The mode lock function ensures consistency when testing injectors.
It can be used with any fuel pressure tester. Gasoline engines only, not for diesel engines.
Explanations for the 4 Modes:
Mode "1": Single pulse mode.
In this mode, when the "Pulse" key is pressed, the instrument will send out a pulse with a pulse width of about 255 ms.
Mode "2": Short pulse mode.
In this mode, when the "Pulse" key is pressed, the instrument will send out 50 pulses with a pulse width of about 7 ms.
Mode "3": Long pulse mode.
In this mode, when the "Pulse" key is pressed, the instrument will send out 100 pulses with a pulse width of about 3.5 ms.
Mode "4": Continuous pulse mode.
In this mode, when the "Pulse" key is pressed, the instrument will output continuously at the rate of 50 pulses per about 1450 ms, every pulse’s pulse width is about 7 ms.
At any time, you can press the "Pulse" key again to terminate the pulse output.
Operation tip: When switching modes, please reset and then select the mode.
Operating Instructions:
1. Turn off the car's engine.
2. Remove the wire plug of the vehicle injector to be tested, and then connect the two pulse output terminals of the fuel injector tester to the vehicle injector.
3. Then connect the red clip of the injector tester to the positive terminal of the 12V car battery, and connect the black clip of the injector tester to the negative terminal of the car battery.
4. Insert the DC plug into the port of the fuel injector tester.
5. Press MODE SET key to select the desired pulse signal output mode, and the screen will display the currently selected mode.
NOTE:
1. Before using this fuel injector tester, the engine of the car must be turned off.
2. Do not smoke or ignite near the car.
3. Do not splash the fuel of the car on the hot engine parts.
4. Only use this injector tester in a ventilated place. Do not inhale exhaust fumes from vehicles and vapours.
5. Do not get close to any rotating (or moving) parts of the car, and do not touch any heat-generating parts of the car.
6. Do not short-circuit the positive and negative poles of the car battery.
7. Do not touch any car parts with dangerous voltage.
8. Always follow the warnings, cautions and related maintenance instructions in the vehicle maintenance manual.
9. Wear qualified goggles.
10. After the test is complete, all disconnected vehicle connections should be properly restored.
Rfam337
Reviewed in the United States on September 23, 2024
This was very intuitive and easy to work with. The adapter is great for cleaning the injectors. The different modes of the tester made it so easy to test and to clean my fuel injectors. The display is easy to read and understand. The buttons even make a click noise, so you know you have pressed them. This is a great tool to have in your garage if you do any basic maintenance to your vehicles.
Chad
Reviewed in the United States on September 18, 2024
Nice tester overall. Nothing too high quality, borderline feels cheap. But does work really well. I’m not a mechanic by trade but do work on and fix my own truck. It’s nice to have this tester handy. Good price
Sunny Side Up
Reviewed in the United States on December 8, 2024
this looks and feels well made. simple to use per the instructions. wiring and connection points feel like they're last for a good while, so this looks like a good choice in my books for having on hand for when an injector gives you trouble.
Kyle
Reviewed in the United States on December 4, 2024
Be careful not to spill any of your carb cleaner or whatever u use to clean the injector or else the exterior can get eaten by the cleaning solution
Vicente Ugarte
Reviewed in the United States on December 30, 2024
Connections could be a bit longer.
Justin S
Reviewed in the United States on November 9, 2024
This tool was great to help me diagnose fueling issues with an older Volvo that had not been running in a couple of years. The instructions were easy to follow and the tool was intuitive to use. Definitely an essential tool for diagnosing fuel issues!
glenO
Reviewed in the United States on October 22, 2024
Kinda cheap and made with light duty plastic but works great. Just be gentle with it-
The Sin Lifter
Reviewed in the United States on October 14, 2024
Looks like the tester is faulty, not providing sufficient voltage. Loss of time with this device.Connected directly to the car battery, the injectors open normally.
Recommended Products