Shopping Cart

Your cart is empty.

Your cart is empty.

Trunk Rear Hatch Liftgate Switch Latch Cover Lid Black, Replacements 84905-47010,84840-21010,84840-35010,84840-47020, Release Button Rubber Cover fit for Avalon Prius Sienna Sequoia 4Runner Camry

Free shipping on orders over $29.99

$6.99

$ 3 .99 $3.99

In Stock

About this item

  • 【Replace】84905-47010,84840-21010,84840-35010,84840-47020,84840-08010,84840-33090,84840-20010,926-098.
  • 【Fitment】Avalon Prius Sienna Sequoia 4Runner Camry, Scion: tC, xB, RX330 RX350 RX400h LS460 LS460L LS4600h GS300 GS350 GS430 GS450h GS460.
  • 【Material】Made of Silicone Rubber, Good touch feeling and it will last longer and withstand the high temperature better, Farewell to dry rotted, sticky mess and be melting.
  • 【Performance】Strong and durable, wear-resistant and scratch resistant, quality is guaranteed, high strength, high hardness, not easy to break.
  • 【Easy to Install】Back Door Handle Switch is very easy to install in a few minutes, perfectly fit in, It can directly replace the old or damaged one.


Product information

Replacement OE part number:

84905-47010, 84840-21010, 84840-35010, 84840-47020, 84840-08010,84840-33090,84840-20010,926-098.

Fitment:

Prius 2004-2009

Sienna 2004-2010

4Runner 2003-2017

Camry 2007-2011

Avalon 2005-2012

SEQUOIA 2008 - 2018

SCION:

tC 2005-2010

xB 2004-2007

RX330 2004-2009

RX350 2007-2009

RX400h 2006-2008

GS300 2006

GS350 2007-2011

GS430 2006-2007

GS450h 2007-2011

GS460 2008-2011

LS460 2007-2012

LS600h 2008-2012

No need to replace the entire latch assembly if only the cover rubber piece of melted.

If you have any questions about the product, please feel to consult.

While this is not a genuine OEM part, it is a direct replacement and good value!


Chris Sharp
Reviewed in the United States on January 8, 2025
The part is okay, but forget trying to use that tool
R. Carboni
Reviewed in the United States on January 23, 2025
I bought this for my 2010 SIENNA, and it appears to be an exact duplicate of the OEM product. I did run into a couple of installation issues which are not the fault of this product or seller. The convenient tool supplied with this item had a different screw head interface than what they used for installing mine at the factory. The tool also did not fit into the awkward location of my tailgate switch. This might be different with later model years as the redesign occurred in 2011. The screws provided were the correct length but too narrow of a gage. I just reused the old ones. It is my recommendation that people installing this should be prepared to use alternative tools. If the old rubber cover is a gooey mess, try to remove all the pieces from around the button so the new rubber piece can effectively grip the edges of the button. It has been working fine ever since I installed it four months ago.
lori
Reviewed in the United States on September 6, 2024
Fits perfect but had to remove inside panel to access the area
Carmine Campana
Reviewed in the United States on July 3, 2024
The cover is good , the screwdriver that comes with it is useless..the angle of the screws on 2008 prius made the tool useless ...tossed it right in the trash
Paul Petrucci
Reviewed in the United States on December 26, 2024
Item came just as it was listed. It works perfectly on my 2010 4Runner Trail.
Alex
Reviewed in the United States on October 29, 2024
Just one problem what I had in installation its remove old glue, but this lid fits perfectly
David J. Hayden
Reviewed in the United States on October 25, 2024
Product was good quality and worked out fine. If I were doing another one, I would get one with the switch and cover. Digging all the plastic off the old switch was a pain.
ST
Reviewed in the United States on October 1, 2024
Closest to the original, sealing the circuits and enabling the trunk opening. Installation may require removing nuts from the inside of the trunk to remove the older casing. Once that is done, new installation is a breeze.
Recommended Products