Shopping Cart

Your cart is empty.

Your cart is empty.

thermowell030cm-SS Tanks and Pipe, 1/2' NPT x 30cm

Free shipping on orders over $29.99

$19.84

$ 9 .99 $9.99

In Stock
  • Length: 30cm/11.8
  • Material: 304 stainless steel
  • Connection: 1/2NPT 304 stainless steel Hex
  • Inner diameter of sensor hole: 7mm
  • For use with &light;7mm od thermocouple sensors, see the Duda Solar Pt1000 & 10K sensors


Thermowells for aid in temperature sensing by duda energy a thermowell is needed in order to use a temperature sensor in a tank or pipe system. These are usually pre-installed inside of a solar tank, however, they may be installed into any port or pipe fitting which has 1/2 inch npt fittings. In pipe installations, use a tee for connecting to pipes. The sensor slides inside of the thermowell once secured into a pipeline or tank. This may also be used as a replacement for corroded thermowells pre-installed into Duda Solar tanks. It may also be used for other temperature sensing applications, such as biodiesel processors and other fluid heating applications. Use the copper thermowell for fast temperature Detection. Stainless steel options are also available for better rigidity and where chemical resistance may be required, such as in biodiesel applications. Inner diameter of the tube inside the thermowell for insertion of the sensor is approximately 7mm. These are best used with the duda energy Pt1000 and 10k sensors. Longer length thermowells allow for deeper insertion into a tank or pipeline. These may be beneficial when it is a large tank or the sensing needs to be in the center of a pipeline. Copper thermowells have brass 1/2 inch hex adapters. Stainless steel thermowells have stainless steel 1/2 inch hex adapters


Denis LAPOINTE
Reviewed in the United States on July 30, 2021
Plastic connector shown in photo was not included. We need to find one
Timothy Bachamp
Reviewed in the United States on June 8, 2019
Very well made. Will be using this in a 30 l fermentation bucket lid to measure temperature of wort.
Ilyapl
Reviewed in the United States on September 5, 2016
I'm using the thermo well with a ds18b20 digital thermometer probe. To get the probe inside the well, the heat shrink wire wrap between the metal probe and the black wire must be cut off, then the metal probe fits easily to the bottom of the thermowell.
Samuel B.
Reviewed in the United States on March 2, 2016
I use this with an STC-1000 probe and the probe is the perfect size to fit in and be pulled out. I will likely end up buying more of these for my lager chamber.
DSR
Reviewed in the United States on October 4, 2016
Perfect thermowell for my brewing buckets! Fits a DS18B20 sensor just fine. I use it with a Rpi for temperature logging. I'd recommend buying this nut to go with https://www.amazon.com/dp/B003GXF5DU/ref=cm_cr_ryp_prd_ttl_sol_20 and a couple of washers.
Joseph S Morris
Reviewed in the United States on January 29, 2016
Fit perfectly for my Ranco Digital probe.EDIT: Not only does it fit the probe, but I found the compression end fitting that had fallen under my workbench when I opened the package and it is great. It works to secure the probe wire in place and insulate the probe end a little against colder air entering the thermowell ( a problem I have when brewing in my cold garage). Added bonus.
Bobl
Reviewed in the United States on April 20, 2016
cheap but works
Sean
Reviewed in the United States on August 28, 2015
It's a little snug for a DS18S20 probe, but you can make it work if you wrap everything up. Fits fine through the top of a fermentor with a grommet on the hole for a airlock.