Your cart is empty.
Your cart is empty.Description: Military level double circuit board design High-voltage condenser ST trigger diode With heatsink Features: Voltage: AC 110V-230V Power: cont. 5000W below; Max. 10000W Voltage Regulation: AC 10V to 220V (Adjust begin 20V) Dimensions: 130 * 60 * 47mm (5.12"x2.36"x1.85") Application: Electric furnace, water heater, the lamps and lanterns that move light, small AC motor, solder iron temperature control and so on(Inductive or capacity load power should be reduced, the voltage regulator is equipped with two way high power thyristor, needn't to add any component can be used , very convenient and practical.) Note: The product needs to be connected to the load and adjust the potentiometer to detect the output voltage change. Package includes: 1 x 10000W SCR Voltage Regulator
Customer
Reviewed in the United States on July 2, 2024
I was not expecting very much when I ordered this power control but it exceeded my expectations. First, it has solid wire terminals to attach my 14 gauge wires. Second, the heat sink allowed for good heat dissipation. Third, it was easy to disassemble so that I could custom fit and mount the chassis. Fourth, the voltage control knob could be mounted remotely with it's 6 inch leads. I was controlling a 240 volt, 1500 watt water heating element, and this control worked perfectly.
MikeDWA
Reviewed in the United States on February 8, 2024
I was skeptical at first to control my treadmill motor, but when I added the 50 amp bridge rectifier, in turn putting a load on it, then the miracle happens it puts out about max 118v dc enough to power my 2.5 hp treadmill motor for my converted mini wood lathe.
Adam
Reviewed in the United States on February 5, 2024
Device needs a load. It seems to work so far on 120v. Could be a bit better quality
Kindle Customer
Reviewed in the United States on February 28, 2024
Not an electrics expert, so I know you *can* use 110 on a 220 device, but I'd rather not.
Bob Sherell
Reviewed in the United States on December 6, 2024
Mailed me a broken smashed up unit
DGewey
Reviewed in the United States on September 9, 2023
I'm not an electronics expert, so I don't know if it will make much of a difference or not, but the product listing lists multiple input voltages (110V, 220v, 240v, etc.) But the decal on the side of the unit itself only says 220v!Luckily my application is 110v, so I'm not too worried about damaging the unit if it IS designed for 220, but for anyone planning on using it for 240 or higher based on the Amazon product listing, be aware that the unit itself doesn't list voltages higher than 220v. So if you're planning on using it with voltages higher than that, you may need to calculate the max wattage of this unit based on those higher voltages, as the max load listed in the product listing may be at 220V.
CA Storm
Reviewed in the United States on October 29, 2023
My main purpose in buying this product was to control an infrared heater so I can set its intensity to my liking. So far, it has passed my test. In both ~75% and 100 % setting, I didn't sense in any dramatic increase in the controller's temperature and no arcing or buzzing at all. See attached picture.I also tested it on a heat gun -- not a real application, just did it as a sanity check. Using this controller, I could vary the motor speed and intensity at the same time from the lowest to highest level.Also notice that I've only tested it on resistive and brushed motor loads. Not sure how it would handle different load types.
Mark A.
Reviewed in the United States on December 9, 2021
This was my first foray into controlling AC voltage with such a thing (used with a DC rectifier to run a 110VDC permanent magnet motor)...works like a charm, although it's worth noting that it was necessary to replace the potentiometer with a lower resistance one to achieve the desired range in volts - the original potentiometer essentially sets the bottom end of the volt range too high for my needs. But that's a cheap fix and a quick one if you're into soldering. Overall, perfectly happy with the purchase. In fact, and if anyone out there needs to cut back on the heat sink - I did to make it fit into an enclosure - I've run it for hours at a good clip (~50-60%) without overheating or burning out the controller...happy news for anyone needing to remove part of the heatsink...
Recommended Products
