Your cart is empty.
Your cart is empty.Product Description
helen
Reviewed in the United States on January 4, 2025
Decent quality dries clear but no matter what I did including following the directions there was still bubbles. Appears decent and is durable. Cure time is good and hardened well. Effective for what I needed
Rick
Reviewed in the United States on January 22, 2025
has to be a good temprchure for for working with it got here ahead of time
Patricia Powers
Reviewed in the United States on September 9, 2024
I have used 2 other brands and been sorry. I had some Ponderosa Pines milled from my property (infected with dwarf mistletoe) and I love live-edge wood as wall decorations, cool shelving, and other projects.The other brands dried funky and were still sticky a week later (Yes, I know how to stir it and followed instructions to a T). Another brand settled in patches and even tho I had spread it properly, it wouldn't settle in other spots.Every time I use SuperClear, it turns out like a beautiful clear, level, even, glassy coating. It shows off the blue streaks in the Ponderosa Pine and brings out the intricate beauty of the bark edges. Looks like a million bucks ! Thanks to you, the makers, for doing an honest job with this product.
Tim Odonnell
Reviewed in the United States on February 23, 2024
Worked and cured well - watch a few project videos first, and you'll be pouring resin like a pro in no time.Very low VOC - can be used indoors without mask as a result, which is HUGE! Make sure your pouring surface and work area is at least 65 degrees F for best results... and keep a hand torch ready, as just a quick pass of the Bernzomatic open flame will remove troublesome and unsightly "bubbles" that form during the early curing phase (before the epoxy sets).Took the dyes flawlessly, I had light gray base with blue and moss green details for walls, snow white for the ceiling (it was a multi-color, multi layer, multi piece custom bath enclosure) - sorry for the blurry image. Project came out looking great, the edges sealed perfectly with silicone, custom fit shower enclosure is 100% waterproof.Beware "buggy" grades of plywood as pouring substrate:I used a construction-grade 1/2 plywood as my flat base - and though nothing of it, as a good strong substrate.But if you use plywood as a base, especially construction grade, be careful as many commercial grade plywoods can have small "bugs" living just below the surface! I was unaware of this, and when my first coat of epoxy went on, I had to spend several minutes and intervals during curing picking "bugs" (small, gnat-like critters) which migrated out from the sub-layers of the plywood. At first i though I had a hole in my window screen, but no, they were coming from inside the plywood, and migrating INTO my lovely epoxy resin!Honestly I have run into this issue before, when 1st-coat painting fresh plywood projects - so it was more of a distraction, and actually did not harm the wood, the piece, or the project. It was just annoying, picking gnats out of setting epoxy... had I used particle board or another substrate, I would not have had this issue, so "my bad" but no harm done.I will definitely purchase this epoxy again: And excellent product, handles and performs very well, easy to use and "master"... looking forward to my next epoxy project!
Roger Marshall
Reviewed in the United States on December 28, 2024
This resin mixed well, poured well, and is easy to use. Be sure to follow mixing instructions carefully. When pouring be sure the surface you are pouring it on is absolutely level.
D. Howe
Reviewed in the United States on October 19, 2024
I have purchased this product several times and I am 100% satisfied with it. It mixes well and is crystal clear. I use it to put down layers onto table tops and to cast resin pens. The table tops pour out nice and I spread it out with a foam paint brush. I only have to get the thickness close as the resin then self-levels. Once it's spread out I use a heat gun to pop any surface bubbles. I then go away for 5 to 10 minutes. I return to use the heat gun to pop any micro-bubbles that have formed. It's hard to see them, but if you look at the surface at a steep angle while passing the heat gun over the resin you can see them pop. I am only passing the heat gun over the resin at the speed you might use a paint brush. I am not trying to heat the resin, just pop the bubbles. Then it's time to wait. 24 hours it's ready for me to apply another layer. I put things like old maps on the table so I will do 3 or 4 layers of resin.With the pens, I mix the resin and split it up into 2 or 3 small cups. I then add special dyes and glitters to each and stir well. I then let the resin sit for 10 to 15 minutes so that when I pour them into the pen mold, the different colors swirl around each other but don't mix together too much.I also tried a Chinese resin and I was not happy with how reliably it mixed. Sometimes it took several days to get fully hard. I have always had 100% success with this American made product and I can always take it out of the mold 24 hours later. I highly recommend this product.
Stephen Avery
Reviewed in Canada on May 27, 2023
I am using this product for a kitchen conter
irene
Reviewed in the United States on November 28, 2023
Pamphlet needs more information about working time and especially when to remove the edge tape. Initially, we waited too long and the top was too set to run over, leaving a scramble to " paint" the extra we saved for fill spots. Then the second half we removed prematurely which had way too much run and alot of drip scraping.Suggest getting a small epoxy kit from a box store and practicing the techniques of mixing,coloring and popping bubbles beforehand.In the end, this was a first project of 55 soft of counter and it is just beautiful! I wanted white with very subtle coloring. We added matte white to the whole pour, with a side cup of light colorant, drizzled and tapped in as soon as we poued. Four gallons, split into two gave extra working time, hand mixed. A good heating hair dryer was used for bubble removal. I will be top coating for soapstone matte finish.Cost effective for a new look and these counters are curvy which would be a huge expense to replace.Minimal smell during use and yes, proper cabinet/ floor protection is super important because this is a very sticky messy project. I'm sure if we knew when to remove the edge tape, things wouldn't have gotten so messy.Totally satisfied as one cannot expect perfection as a first time user with so much area to cover.
Harold Pépin
Reviewed in Canada on November 24, 2023
Bien
kkozak
Reviewed in Canada on June 2, 2022
I’m new to epoxy resin. The instructor used this brand at the work shop I went to so I bought some to use at home. It mixed up really easily 1 to 1 ratio. There was an odour so make sure you open a window. Definitely wear gloves it’s hard to wash this stuff off . This is the best results I had yet.
louise
Reviewed in Canada on December 22, 2022
très bon produit
ian Customer
Reviewed in Canada on November 8, 2021
I found this epoxy to work well but to have more bubbles stay inside after pouring into molds than other brands. I don’t use heat guns so I’m usually left with usually tiny bubbles in at least some molds, but works fine despite that. Cures well. Weird that you have to first use the B bottle epoxy then add the A bottle to it, but whatever works. Fun craft. Makes great artistic gifts. Pops out of molds easily without using oil.
Recommended Products