Your cart is empty.
Your cart is empty.Product Description
FL MOM
Reviewed in the United States on March 7, 2025
I had a broken 1/4 -20 tap and thought i would try these carbide end mills to remove it. I used up 2 of them but was able to remove the tap a little at a time running about 400 rpm. Good product.
Ken M.
Reviewed in the United States on February 6, 2025
Works like it should
Oldshoes
Reviewed in the United States on February 23, 2025
Hey – Guess what 'Speed Tiger' sells? They sell end mills. They don't sell dog clippers, nose hair trimmers, party balloons, adult diapers or kitchen sinks. They don't obtain their products from a whole sale truck. Their motto is: Speed Tiger – Striving for Excellence. I believe 'um. They're one of three companies I go to for affordable, quality end mills. I first gave Speed Tiger a try when I needed to cut a 5 foot x 3/16” key way in a reversing rod that I fabricated for my '53 Monarch lathe. I used a Cr flavored boat prop shaft for the reversing rod. I bought a 5 pack of 3/16” Speed Tigers. They were the same flavor as these beautiful 5/8” - four flute micro grain with the AlTiBN coating. In fact, under a 5x glass the 3/16ths look just like these 5/8”. I burnt up the first 3/16” in the five foot keyway, the second was none too happy when I swapped her out for a fresh end mill to make the final passes, but she was still cutting. Yeah, I probably could have bought a higher quality cutter for 50 bucks and maybe finished the whole cut with one cutter – maybe. I didn't - I bought (5) speed tigers for 35 bucks and still have 3 good 3/16” end mills – (two are virgin). I've done some cuts with these 5/8” big brother of those 3/16” on the same CR flavored SS – Scraps from the reverse shaft. Test cuts were made between 500 and 550 rpm. Cuts look great, finish would be better if I spun them a little faster – I'll save that for when I really need it. These 5/8” Speed Tigers look no worse for the wear.I can't afford the Kennametals - even if I could I wouldn't buy them right now. I'm not a machinist – I do a lot of machining – but I'm not a machinist. I don't have any production woes to keep up with, and time ain't money when all you have is time – and time would be about all I'd have if I burnt up a 300 dollar end mill due to a calculation error. I like the Speed Tigers – they make quality end mills that do what I need 'um to do, they last, and I can still afford some rice and beans.7 Super Novas for The SPEED TIGER EISE 5/8" 4 Flute 2 pack - AlTiN Coated, Micrograin Carbide End Mills ~ Thanks for Reading – Have an Incredible Life! ~
Erik
Reviewed in the United States on February 2, 2025
Did a lot of milling with one bit on stainless steel, which is hard on any end mill. It's still clean and sharp.
bndrrw
Reviewed in the United States on February 15, 2025
I'm not saying I used one of these to deepen an existing 36mm x 104mm slot from 3.5mm to 8.5mm deep in a 1018 steel plate with a dewalt trim router at 16k RPM, because that'd violate some safety rules.But I am saying that this is a fantastic endmill that could definitely do the above without breaking a sweat (or endmill) and leave a clean surface finish while it's at it.
Dino
Reviewed in the United States on January 29, 2025
Pleasantly surprised how good the quality is.
Customer
Reviewed in the United States on September 24, 2024
Fast cutting in oak
Brian Eastwood
Reviewed in the United States on December 17, 2024
Nice quality bity, cut well and would pick them up again
Recommended Products
$11.70
$ 5 .99 $5.99