Your cart is empty.
Your cart is empty.Product Description
Ultra High Brightness LED Light
- Operation Type: Latching / Maintained
- Mounting Hole Size: 22mm / 0.87 inch
- Switch Rating: 5Amp 250V
- Material: Stainless steel 304 shell, Sliver contact, Copper gold-plated pin
- Temperature Rating: -40 to +70 Degrees Celsius
22mm 7/8" 3-Position Latching Selection Switch
Select Switch 3 Positions 90º，The distance between the each positions is 45º .
- Installation dimensions: ∅22mm DPDT (2 Normally Open+ 2 Normally Close)
- The shell of the selection switch is made of stainless steel 304, which is very hard and sturdy, and will not rust.
- Wide Application: It can be used for device switch control, energy regulation, mode switching circuit selection, position sensing, and other aspects.
- Specifically, it can be used in desk lamps, coffee machines, machines, fans, equipment, instruments, and DIY products.
- IP degree:IP54 Waterproof.
Stainless steel 304 shell
Stainless steel 304 shell, sturdy and durable, will not rust.
Copper gold-plated pin
High quality material, copper gold-plated pin, excellent contact.
Wire Socket Plug
Equipped with dedicated connecting wires, with a length of 150mm/5.9 inches. Red Wire: Normal Closed Pin；Green Wire: Normal Open Pin; Black Wire : LED “+”; White : LED “-”; Blue Wire: Common Pin.
Red/Blue LED Light
High brightness LED light, with a lifespan of 40000 hours and a voltage of 12V-24V, without distinguishing between positive and negative poles.
Mack H.
Reviewed in the United States on February 13, 2025
Received fast and as shows
Kevin Garcia
Reviewed in the United States on September 23, 2024
Two wires power the LED, not associated with any switch, it needs 12VDC. This is a DPDT switch. There are 3 positions, center, turn to LEFT, and turn to RIGHT. In the center, each common in connected to its NC. When you turn the switch to the left(it stays, NOT momentary), the the left common is connected to the NO, and the right common stays connected to its NC. When you turn the switch to the right(it stays, NOT momentary), the right common is connected to its NO, and the LEFT's common to its NC. The switch is perfect. Not all the switches have all the options-- this switch has 8 wires, 2 for leds and three for each independent SPDT switch(2 spdt switches make a dpdt of course).
Bruce S
Reviewed in the United States on September 10, 2024
Fit exactly in the cast hole on my PM-935TS mill, click left the cabinet light comes on, click right and the halo ring light on the quill comes on.
pm
Reviewed in the United States on May 15, 2024
Not sure why it gives you the option for 2 power supplies. I guess there might be a few situations where you would want that... But how I hooked it up was the blue wires and the black to positive, white to negative, 1 green to 1 light, the other green to the other light. I did not use the reds. The reds also turn on with the corresponding green wires. So if you want the leds to only be on when the switch is on wire the reds to the black. Hope this helps someone with the lack of installation instructions.Other wise it's connected to power supply that my dimmer switch controls in my miata and it does dim a bit which is cool. Does feel way cheaper than expected. Looks better than it feels lol.
HARDCORE FISHING INC
Reviewed in the United States on December 12, 2024
I had a touch button but the location on my boat when it got wet would turn it on. This is the perfect solution for my application. I did have to return to the Amazon product page to figure out how to wire it correctly. the instructions were kind of vague.
Jscarin
Reviewed in the United States on November 11, 2024
I put this on my harley-davidson tour control driving lights. When installing it, I noticed that there is no locking mechanism, it just pushs together. When you hit a bump in the road it kept coming undone. I used tape and shrink tube to hold it and it didn't help. They need a better design to keep both pieces together.
allen
Reviewed in the United States on November 11, 2024
as listed
David Hoffman
Reviewed in the United States on November 27, 2023
The red and blue wires are swapped. Red is common and blue is NO.Switch works good for low current circuits. Looks nice.
Recommended Products