Your cart is empty.
Your cart is empty.Product Description
Product Specifications
Maximum pressure rating of 300 psi,Temperature range of -40 to +250 degrees F.
1、One head is 1/4 inch Barb the other head is 1/4 inch NPT
2、One head is 3/8 inch Barb the other head is 1/4 inch NPT
With these fittings, hoses can be customized to any length, meet your many needs.
Can be used in any environment, from home garages to professional auto shops.
High Quality
Durable Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
With Teflon Tape
2pcs with 1 teflon tape.
4pcs wih 2 teflon tape.
simply wrap the tape around the threaded male end of the pipe.
Clear Thread
Manufactured in strict accordance with American thread standards, the thread is clear and easy to use
Step 1
Cut off the damaged part with a pipe cutter ,put the nuts on the hose.
Step 2
Twist the 1/4"(3/8") Barb into the hose
Step 3
Tighten with a suitable wrench or by hand (to prevent hand injury, please wear gloves)
Step 4
Installed, as shown above
Daguimar
Reviewed in the United States on September 4, 2024
Excellent product and seller!
Diego W.
Reviewed in Canada on September 29, 2024
Time will tell its quality.
Customer
Reviewed in Canada on September 28, 2024
Good quality brass
Michel Mimeault
Reviewed in Canada on September 24, 2024
Répartition tuyau
D. Abbotson
Reviewed in the United States on August 25, 2024
The list dimensions are wrong in the picture for the 1/4 hose. They are larger than shown in the illustration.
Jed kramer
Reviewed in the United States on July 12, 2024
I like how it's constructed but I needed it for larger caliper hose. Be great fixing smaller hose tho.
Dieselgrady
Reviewed in the United States on December 4, 2024
Had a leak in one of the fittings on an old 50' air hose. Compressor was cycling more than it should so started looking for air leaks. Found it at the point where it attaches to the quick coupling into the compressor. The hose was made of polyethylene so hoped this fix would work. Seemed very tight, but heated the hose and pushed on the fitting. Used a few wraps of teflon tape (supplied), connected it to compressor and leak problem solved.
Brian
Reviewed in the United States on October 23, 2024
I have a garage air compressor and the red rubber air line was bulging at the end. So instead of spending $30-40 on a new hose I figured I could cut off 3 inches replace the end. This isn't even close to fitting over the hose. It might work on plastic poly line but not rubber air hose.
Jean S Hanna
Reviewed in the United States on October 14, 2024
Good item with good price
Disappointed
Reviewed in Canada on January 23, 2024
It's 3/8. I bought this to fix a 12V compressor & need 1/4 inch not 3/8. Good thing I used original equipment with new hose & a clamp.NO STARS GIVEN!!
chuckntx
Reviewed in the United States on February 27, 2023
These are stated to work with 3/8” air hoses. They do, but only after I enlarged the tube hole on the tightening cap side. I do have slightly oversized hoses, so that may have played a part, but they had to be modified nonetheless. Works very well when all was said and done.
D. Beaver
Reviewed in the United States on October 12, 2023
The 3/8" fittings will ONLY FIT on POLY HOSE, they WILL NOT FIT RUBBER HOSE. The outside diameter of rubber is larger than that of poly.It's a tight fit on the poly hose, which is a good thing, but it is a challenge to get the fitting onto the hose then threaded in. But it's a good tight fit, no leaks. So for what it is, it's a good product.- djb
Cindy H.
Reviewed in Canada on April 10, 2023
This might look like what you need but it won't fit. It's way too tight. Get the Metabo version. That is also tight but not impossible like Breezily item.
Recommended Products
$24.69
$ 11 .99 $11.99