Your cart is empty.
Your cart is empty.Product Description
Powerbuilt 1/2 in. Dr. 36mm Axle Nut Socket
This Powerbuilt axle nut socket is a high quality, durable 1/2" drive impact-rated 36mm socket forged from chrome molybdenum steel. We made this impact grade, 6-point socket extra deep to fit various axle lengths. Designed for quick axle shaft nut removal.
- 1/2" drive 36mm socket designed for removing axle shaft nuts
- Forged from tough impact-rated chrome molybdenum steel
- Impact grade and extra deep to fit various axle lengths
- Meets or exceeds ANSI standards
Customer
Reviewed in the United States on February 17, 2025
I had too big and too small and was tired of borrowing from friend. Npw they can borrow from me. Good quality at great price
Álvaro
Reviewed in Brazil on February 12, 2025
De boa qualidade e reforçado.
Jörg H.
Reviewed in Germany on January 27, 2025
Schnelle Lieferung und Ware ok
Trash Pile
Reviewed in the United States on January 1, 2025
Worked great with 1/4 zip gun to remove 3rd gen 4Runner axle nut. One note, if you’re using hand tools, it’s just barely deep enough to do with the tire on, but would be 5/5 if socket was a bit deeper. Again, did the trick and should last the cars lifetime. Recommend.
WESIII
Reviewed in the United States on September 27, 2024
I’ll be honest I have never found a bad impact socket. Maybe guys that use these all day everyday split them or somehow break them, but I haven’t. This is a solid socket. Fits perfectly and is made in Taiwan. They make some solid tools. Priced right and well marked.
Bob K
Reviewed in Canada on May 20, 2024
Perfect socket for my needs. Most H/D axle sockets only have 1" nut flanges then machine a smaller hole for the axle shaft. Needed a special socket for Cummins front mounted engine mounts on a Transit Bus (20mm nut with limited access). Will have to cut 3/4" off bottom of socket to shorten it to fit around crankshaft pulley which will still leave 1" to grab the nut. This one has nut flanges machined almost to top of socket a true 1 3/4" DEEP socket ... hard to find this in any description in Details section. Narrow 1/2" drive section at top is extra bonus for limited access areas. True one day delivery as well.
Charles Carroll
Reviewed in the United States on February 10, 2024
I purchased and used this socket for a different application. But This little socket turned out to be the best thing for a BMW 2006 X3. I had to change the oil in this car for an elderly person who could not afford BWM service prices. BMW service department would not sell me a oil wrench for for this car, even after I explained the situation. Which is against the law in my Stare we have the right to repair law, Germany does not set policy in a US State!. However I was able to figure out that on the top of the oil case filter holder there was 36 mm molding on the case. Which this socket worked beautifully. All the BMW service manager at the shop had to say is use this size nut on the oil filter housing, and you'll be fine but he was not a human being.
Tamer Altelbani
Reviewed in Saudi Arabia on November 28, 2024
خامة نظيفة وسعر مناسب
Customer
Reviewed in Canada on November 27, 2024
Got the job done. Does what I needed it to. Seems like good quality and good value. Only use it so often cause it is such an odd size. Would recommend to anyone who needs this.
. Chaudhry
Reviewed in the United States on November 17, 2024
mostly used on jeeps great strength works great so farhope to last long
B. Eaton
Reviewed in the United States on October 9, 2024
Used it for its job as an axle nut remover. Worked twice and expect it to work again if needed.
Edward Tackabury
Reviewed in the United States on October 27, 2024
Works perfect. Good material.
Recommended Products