Your cart is empty.
Your cart is empty.Upgrade your vehicle’s performance with the Pertronix Electronic Ignition Kit, the ultimate solution for replacing outdated mechanical points. Designed for a seamless fit into your existing distributor, this ignition kit enhances your engine's efficiency without the need for an additional ignition box, preserving the classic appearance under the hood. This innovative kit doubles the voltage delivered to your spark plugs, increasing horsepower, improving fuel economy, and extending spark plug life. Its advanced technology uses rotating cobalt magnets paired with a Hall Effect integrated circuit, ensuring precise timing without the wear and tear of moving parts. The robust, maintenance-free design is epoxy molded, making it impervious to dirt, oil, grease, and moisture. Ideal for a wide range of applications including automotive, marine, industrial, and agriculture, the Pertronix Ignitor is easy to install and offers stable, reliable performance with no adjustments necessary.
X-FACTOR Automotive
Reviewed in the United States on June 26, 2024
It is and had been working great. Starting and running is much improved
A.P.B.
Reviewed in the United States on August 8, 2022
Works as should, happy to have saved quite a few bucks over dealer pricing.
mike
Reviewed in the United States on March 17, 2022
Easy install and works.
Chris g
Reviewed in the United States on April 6, 2019
I installed with a new distributor. The quality of the wires are not good. I also tossed the ring terminals, they are crap. If you do this swap, get some quality 3m or anchor terminals. I think pertronix could have came up with better power wires, but hopefully they'll hold up.
Patricia Jarrett
Reviewed in the United States on August 31, 2018
I had been thinking of buying this conversion for quite a while. So when I needed to replace the points and condenser I decided to put that money toward the PerTronix Kit. I just had to make sure I had an Odd Fire engine as someone else had transplanted it into the Willys. I read that some people had not pulled the distributor to install the kit, but after looking at it for awhile I saw that to get it right it would be easier to pull it. That was the smart thing to do to get he clearances correct and I needed to install the spacer above the drive gear for the correct up and down play. It was also good to lube and free up the advance arms and base plate---these are old engines. put it all back together and installed the PerTronix coil with it, it fired right up. Adjusted the timing with my light and it is running great. Seems to run smoother and has more low end power. It will pull down to a very low RPM and keep running. This is the second PerTronix unit I have purchased. I put one on my 1958 Massey Ferguson tractor and it has been running better that ever for five years now. PerTronix Kits seem like well made systems worth the money. Would diffidently but again.
L. Hua Po
Reviewed in the United States on July 1, 2017
Wow! Installation was reasonably easy, getting proper clearances a little touchy but OK for an amateur. I found that my old distributor must be rather worn, the final clearance varies from one side to the other, just barely within the tolerances required. But the main point is that my old Jeepster starts and runs so much better! I did find, however, that I had no spark at all with my stock or my "high-output" aftermarket coil, I had to buy the Pertronix coil with more internal resistance---so it all cost $30 more than I expected. My advice is to buy their coil to start with if yours doesn't measure >3 ohms internally. My old Jeepster with the Buick-style V6 went from a hard starter to instant firing, so I feel the effort and cost was well worth it.
Karl K.
Reviewed in the United States on June 21, 2017
for 66' willies/kiaser cj5, it never ran so good as after this hall effect pointless item as installed, follow the directions and you will be fine.
John N
Reviewed in Canada on November 5, 2017
Great product and easy to install, works beautifully.
Monroe Williams
Reviewed in the United States on August 12, 2014
Installed this in a 1967 Jeep CJ5 with the 225cid "Dauntless" V6. Installation was pretty simple, if you can change the points/condenser you should be able to do it without any trouble. The only minor complication I had was that the grommet where the wire exits the distributor (which you need to remove and replace with the grommet included in the kit, to make room for the two wires from the Pertronix unit) had hardened with age and I had to break it up with a screwdriver to get it free.The instructions I received didn't mention one important detail -- the sensor ring can be installed in two different orientations, only one of which is correct (the square notch in the ring needs to be on the same side as the square hole in the plate that holds the mechanical advance arms). Google around for "pertronix dauntless" and you'll find some good pictures in various Jeep forums.I didn't have to remove the distributor or even loosen the hold-down bolt. After the install it started up on the first crank and seems to run better than ever!
Recommended Products
$100.17
$ 48 .99 $48.99
$192.41
$ 79 .99 $79.99
$106.10
$ 45 .99 $45.99