Shopping Cart

Your cart is empty.

Your cart is empty.

No-Clean Silver Tin Lead Solder Paste, Soldering Paste For PCB/IC/BGA/SMD CELLPHONE CPU Repairing(30G)

4.4 (8) Write Review
Free shipping on orders over $29.99

$13.99

$ 6 .99 $6.99

In Stock
  • Essmetuin Solder Paste Content: Alloy Tin 62.8% Pb 36.8%Ag0.4%, Solder Flux Content: 10.8%
  • Lead-Containing Solder Paste - Medium Temperature Solder Paste With Flux, Melting Point: 183 ℃ (361F)
  • Product Advantages: Pushing-Type Design Smoother Flowing No Wasting During Welding
  • Widely Used In BGA /SMD Circuit Board,Motors, Lighting, IC, TV and Other Household Appliances And Industrial Equipment,Sensors, Wires, Fuses, Phone,Metal Shells, Motors, Lighting, Connectors, ,SMT Maintenance


Product Description

Product Description

SOLDER SATINED GLASS

WHY CHOOSE US？

solder paste

Product Specification：

Brand Name: Essmetuin
Model Number: SPA3684
Material: Tin\Lead\Silver
Product name: Solder Paste
Net Weight: 30g
Melting Point: 183°C(361°F)
Feature: High Thermal Conductivity And Conductivity.The Post Soldering Transparent Residues Are Non-Conductive, Non-Corrosive And Highly Insulated
Application: BGA /SMD Circuit Board,Motors, Lighting, IC, TV and Other Household Appliances And Industrial Equipment,Sensors, Wires, Fuses, Phone,Metal Shells, Motors, Lighting, Connectors, SMT Maintenance
Usages: Welding Tool

BGA Planting Tin

BGA Planting Tin

PCB Repair

PCB Repair

IC Chip

IC Chip

SPA

Evan Gelical
Reviewed in the United States on February 5, 2025
Good stuff. At least for what I used it for..smd's, smd LEDs, etc..on copper and aluminum substrates.. super strong weld and melts way before the heat is to a point that an LED couldn't take it anymore.. HIGHLY RECOMMEND
kurosh partovi
Reviewed in the United States on February 5, 2025
Melting temperature is higher than what is advertised.
lane hoskins
Reviewed in the United States on February 12, 2025
It works
Don
Reviewed in the United States on January 8, 2025
This worked and I was able to replace my SOP memory without issue. The temp recommended was to low to reflow. 183C/360F didn't work. I had to move the temp to just over 287C/550F and it worked flawlessly. It could probably been done a bit cooler but I was impatient and wanted this completed to ship to a friend.
P. Heller
Reviewed in the United States on July 22, 2024
I needed to replace a USB-C port charging connector on a Snap-On flashlight. You do not need much and the fact that it is tin/lead. I also used Kester flux prior to laying a tiny bead of paste. I keep the paste in the freezer. It worked and I cleaned it off with IPA. Snap-On wanted $85 to exchange the flashlight with a repaired one. So far, the port still works well. I would buy it again or recommend it as a cost effective tin/lead paste.
James M.
Reviewed in the United States on June 23, 2024
I have not yet used it, but I’m sure it will work well.
chris cooper
Reviewed in the United States on February 8, 2024
Had to replace some surface mounted pre-amps in an expensive audio mixer. The spec said they could not go over 230^C so the safe answer is to use a controlled temp hot air solder station, this flux/solder rated for 183^C (or roughly 400^F) worked beautifully !!! I am sold!
Rob R
Reviewed in the United States on April 14, 2023
Excellently made, several applicator tips provided. The application of solder paste to PCB pads is easy. However, due to the viscosity of the paste, sometimes it did not stick easily to the pads. Still, the past was just right for hand component placement keeping the component in position while hit with hot air to reflow the solder. Melt temperature was a bit higher than I expected and significantly higher than the label (I did not quantitatively measure the actual melt temperature on the PCB). No minuses with this product.