Shopping Cart

Your cart is empty.

Your cart is empty.

Multifunction Time Relay, Time Delay Relay Delay Relay Board DC 12V 8CH LED Multifunction Digital Delay Time Cycle Timing Relay Switch Module

Free shipping on orders over $29.99

$24.85

$ 12 .99 $12.99

In Stock

About this item

  • MAXIMUM LOAD:10A/250VAC,10A/125VAC,10A /30VDC, 10A/ 28VDC,10A/ 12VDC
  • FUNCTION: 6 kinds of functional modes, each functional module has three sub-modes (no cycle, 2-99 cycle, always cycle).
  • SAFETY: High Q value SMD electrolytic capacitors, good responsiveness and low attenuation of in circuits.
  • GOOD FEATURE: 8 channels relay,each channel independently triggered independent delay, do not interfere with each other.
  • SATISFACTION GUARANTEE: We care for every customers feeling.If this product does not meet or exceed your expectations,please send it back for a refund no questions asked.




Specification:
Working voltage: DC 12V
Maximum load :10A/250VAC,10A/125VAC,10A /30VDC, 10A/ 28VDC,10A/ 12VDC
Size:12*6.4cm/4.7*2.5in
Weight: Approx.132g/4.7oz


User Instructions:
Short press: press key time is less than 2 seconds;
Long press: press key time more than 2 seconds;
Status: working status , set status, power-saving status.
working status : start work after powering. Displays the remaining time of 1 channel, the parameters can be displayed the "channel select" to set;
Set status: short press the "SET" key to enter "channel select" Status. Short press "OK" button to exit the setting;
power-saving status: in this Status,digital tubes donot display,and other features work correctly. Long press "OK" button after 5 seconds to enter power-saving status, press again "OK" button for 5 seconds or re-power to exit power-saving status.
Factory settings: press and hold "++" and "--" two button for 3 seconds, to factory settings, and the digital tube will turn open . After re-power , will run default parameters.

Package list:
1 x Multifunction Time Relay


dmkbmw81
Reviewed in the United States on March 5, 2025
So, the lack of documentation is an incredibly serious flaw. Also, it appears that one cannot use this as a delay off relay module. It will come close with F2, but the time counts down after a specific pin receives a signal, and to keep it on you would have to pulse the signal, which is really impractical. I have another delay off module from another seller that works, but only one relay, and I need at least 8. Very disappointing.
Murad
Reviewed in the United States on November 10, 2023
Absolutely perfect !!!
Larry D.
Reviewed in the United States on December 3, 2020
The instructions are, well, there are no instructions! No idea why retailers don’t provide, maybe it’s because it’s made in China, or they’re just too cheap to care. Who knows, it seems to me some poor ratings of like items might be due to the end user not knowing how to program and its functions. At present, the unit appears to be functioning well and seems stable. If time demonstrates a different outcome, I’ll report. But for now, here’s instructions on how it functions and parameters for programming.Walfront 8CH Delay Cycle Relay TimerConnections:VIN, GND, In1, In2, In3, In4, In5, In6, In7, In8.VIN = positive voltage inGND = negative voltage inIn1 through In8 - To trigger relay(s): connect dc-(GND) to any “In1” through “In8” connector.Each relay will trigger to its independent programming.Controls:Set, ++, --, OKSet = Short press enters Programming – repeat press will toggle through functions and parameters++ = increases Function and event duration-- = decreases function and even durationOK = single press = enter – double press = displays timer – hold 5 seconds = turns display off/onFunctions:F0, F1, F2, F3, F4, F5F0 = NO – F1 = NCF2 = NO – F3 = NCF4 = NO – F5 = NCF0 & F1 is controlled by parameters; 2 (seconds), 3 (minutes) & 4 (hours). Relays are ON for the time noted by 2, 3 & 4. Off for same duration. Parameters 5, 6 & 7 do not function for F1 or F2.F2 & F3 is controlled by parameters; 2 (seconds), 3 (minutes) & 4 (hours) -AND- parameters 5 (seconds), 6 (minutes) & 7 (hours). Parameters 2, 3, & 4 control the duration of the relay on, parameters 5, 6 & 7 control the duration of the relay off.F4 & F5 are similar to F2 & F3 but will be triggered upon powering on of the relay board.In all functions (F0 – F5) parameter 8 controls repeat cycle (8 set to 0 = continuous cycling. 8 set to 1+ controls the number of cycles. Note: each cycle of either “on” or “off” is considered one cycle. See Parameter Outline for more information.Parameters; 2 through 8:2 - duration in seconds3 - duration in minutes4 - duration in hours5 - duration in seconds6 - duration in minutes7 - duration in hours8 - repeat cycle time: 0 = continuous, 1+ = number of cycles, see cycle note.Cycle note (parameter #8):Setting to 1 will cycle the relay one time. From NO to closed back to NO.Setting to an even number will cycle the relay then rest on the opposite beginning position of the relay. If relay began as NO the relay will cycle then rest on the opposite position NC.Setting to an odd number will cycle the relay then rest on the beginning position of the relay. If the relay began on NO the relay will cycle then rest on the same position NO.
Recommended Products

$13.89

$ 6 .99 $6.99

4.6
Select Option

$39.03

$ 19 .99 $19.99

4.9
Select Option

$83.41

$ 37 .99 $37.99

4.3
Select Option

$59.47

$ 29 .99 $29.99

5.0
Select Option

$17.00

$ 7 .99 $7.99

4.4
Select Option