Your cart is empty.
Your cart is empty. Mokose Webcam Stand, Stands Bent 360 Degrees for Mounting on a Monitor or Laptop Mount with 1/4" Thread
Weight: 35g
Dimensions: 104*37mm
*Recommended not to mounting Webcam more than 200g *
Ericman967
Reviewed in the United States on March 9, 2025
I attached my Litra Glow to this for a monitor mount and it's great! The Litra doesn't come with a great mount if your monitor has a hump on the back (i.e. not super thin). This works well. The Litra is top heavy...so it'll tip over front-wise if you angle the light too far forward. Otherwise, it's perfect.Build quality is good, it's flexible, and a smart little design. Decent value for the money.
Steve H.
Reviewed in the United States on February 8, 2025
This is waaay overpriced for what it is. It's flimsy and not a secure way to mount a substantial webcam. I have a Mevo Start and the image was shaky due to mild monitor movement. It held the camera but seemed very top heavy and unstable. Ended up returning this in favor of a small tripod. It might be good for very specific scenarios with light webcams, but is still not a $10 item.
Sophia Jensen
Reviewed in the United States on January 9, 2025
I’ve been struggling to find something that would work with my webcam and monitor. I had a stand for a long time but couldn’t get it to sit quite right on my desk around my monitor. My monitor is super thin so typical mounts just didn’t fit right.This is perfect!! The design is way sturdier than expected and was super easy to set up. Had it up and plugged camera in within 2 minutes. Didn’t even need to adjust the camera. Most inexpensive option I found too!
Manal
Reviewed in Canada on June 12, 2024
I don’t like it, it keeps moving around
djwilliamson
Reviewed in Canada on February 18, 2024
I'm very satisfied with the customer service, thank you StarLineStore.
DadOfTeens
Reviewed in the United Kingdom on December 7, 2024
It holds a webcam in place on top of the screen. What more can you ask for.
Bearded Atheist
Reviewed in the United States on October 5, 2024
Cannot hold the weight of a very light brio 4k camera and a ring knockoff light. Ring light has a thread that the webcam screws into and the ring light has a stand with a spot for a 1/4 thread where this mount went, and it just wouldn't support the weight, and the stand doesn't hold its shape. Was looking at other reviews that said to add tape and yeah, I can't do that with a $900 monitor since I just redid my setup to be a clean setup with no mess. The stand itself is not strong whatsoever and the screw goes all the way through when tightened all the way. It looked to be exactly what I needed but was just made too cheap for what I needed. Ended up needing a more expensive clamping stand for my desk after all. Too good to be true, and it was in my case. Returning first thing tomorrow.
Steve Pursell
Reviewed in the United States on October 17, 2024
Would wiggle every time I typed; eventually the rubber tore and now it won't support the webcam.
ミナオス
Reviewed in Japan on August 5, 2023
LGの39.7インチ/5K2Kモニターを購入したら、奥行きが長すぎてウェブカメラを設置できず困っていたところ発見しました。写真のとおり厚いモニターでも安定感があります。
John C Fox Jr
Reviewed in the United States on January 18, 2023
I don't understand all of the reviews that says this is flimsy or unstable. I find it to be neither. Yes, it's unassuming and simple but it works. It stays in place and holds my webcam on top of my monitor very well. And without a giant gooseneck arm catching my attention. I don't even know it's there. The bezel on my monitor is very small yet I still don't see this mount in the screen. I highly recommend this.
S.T.
Reviewed in the United States on October 12, 2022
It's well thought out, with one exception: sturdiness. It'd be hard to make this sturdy and universal though. The case of my monitor is pretty thick (LG 4k UltraFine for Mac -- I can't be bothered to actually measure it, but if it's not a full inch thick it's close) and this still fits.If I wanted this to live on top of my monitor full time I'd use a little bit of low profile 3m mounting tape. In fact, I think that the manufacturer should probably include a couple of pre-cut pieces in the package for just that purpose.For my purposes it's fine. I'm using this with a tripod cell phone holder to hold my iPhone on top of my monitor for use with continuity camera, turning my iPhone into a top notch webcam whenever I need one, which isn't all the time. So being able to reach up and just pull it off the monitor is a feature to me rather than a bug.
largenostril
Reviewed in the United States on April 25, 2022
The default mount that comes with the Logitech Brio 4K webcam had a slight overlap with the viewable area of my monitor (HP x34) due to the thin bezel of the monitor.This mount was a perfect solution! The Brio's mount has ~12mm of overhang while this Mokose mount has ~7mm of overhang. This just clears my monitor's viewable area with ~0.5mm to spare.Very easy to install. The flexible "arm" is sufficiently rigid to hold in place on the monitor. I did add a small strip of double-sided foam tape at the very bottom of the arm to prevent any movement. The silicon surface of the arm doesn't offer much friction against the textured backside of my monitor. This wasn't inherently a problem, but I don't plan to move the mount around often (ever?).The screw mount "hump" could be a bit more adjustable. It's sufficient for my needs, but the range-of-motion is a bit limited and would be the only area I could suggest improving.Overall, super happy with this purchase.NOTE: if you have a Logitech Brio, the original mount actually pops off (give it a good tug or rock it laterally) to reveal a 1/4"-20 threaded insert that attaches to standard camera mounts (like this one).
Recommended Products
