In theory, this 32” door threshold seal looked fine.Installation was straight forward and for 2 months it performed as expected at the door between my home interior to my heated garage.The problem; however, is that the rubber bumper seal seems not to be able to be stepped on.The rubber channel ribs tear from the bumper.I expect to replace door seals and weather stripping as part of regular maintenance, but getting only 2 months or less is unacceptable.I will be trying to contact seller for a refund.

Ordered correct size, but really no way to secure it to concrete. Have screws, but would have been nice to have another way to secure.

Worked perfectly for a door I installed to close in a screen porch.

And to keep the bugs out. Just have to make sure your doors not too close to the ground.

For the price you can not beat this threshold I bought one a few years back and loved it ..super easy to install..I found myself in need of another one ..and came back to Amazon hoping I could still buy the same and hallelujah they still have And at the same low price !!

The rubber piece is actually easy to install. Align the edges of the rubber strip in the groves and press down from the top of the rubber to set in the grove.

This threshold is made of high quality materials. I installed it for an inside garage door that leaked cold air at the bottom. It went in well and looks nice. I am very happy with this item.

Fitting of vinyl should be reviewed, the profile is not the best for the aluminum base

Cut to fit and installed in just a few minutes. Exactly what I expected. Rubber can be tricky to insert but just start at one end and it'll go.

My husband bought this to seal his garage area and it works very well from rain not getting into his garage.Best product and looks great as well.Very easy to install and cut to size.

Fast shipment, low price, good quality, USA made. Aluminum threshold same as old one, but rubber strip now thicker, fits groves a little differently and tough to install. Follow directions. I used soapy water, thumb pressure center of strip.

Can't really comment as I never used it

It's in. And it works. That being said, it's a long road to getting there. My old threshold lost its gasket and was scruffy and dented, and also had screws in front of the gasket toward the outside. The M-D has hidden screws under the gasket. I unscrewed the old one, banged it out from its long standing spot and then lined up the new one. It looked like it was the perfect length, so I banged that into place (a tight fit under the trim boards, but so was the old one). Looking good so far. I drilled 3 pilot holes into the cement using the 3 holes in the threshold, then banged it out again so I could drill the 3 holes and insert anchors for the provided screws. I used a fresh, new cement bit and created holes for my anchors and deep enough for the included screws. Of course before going to such lengths I thought let's just test out the gasket installation since so many had problems. I tested it while it was uninstalled, merely squeezing an end of the gasket into the very tight channels on the threshold. At first it didn't seat properly. Then I made more of an archway in the rubber to get the edges lined up better in the grooves. That worked... again, still only a practice run. I thought, okay, it seems to line up, all I need to to is bang the metal back into place, screw it into my new holes, and then fit the gasket in and I'm good to go with my newly trimmed door resting snugly against the rubber. Perhaps you can guess this didn't go easily. When the threshold is screwed to the floor it's like there's a structural change or something that takes place. The gasket becomes nearly impossible to get fitted into the channels. But with the help of a few tools, soap, and great PATIENCE after swearing like a proverbial sailor, I managed. Here's how: 1. keep the gasket warm until ready to install 2.while still in the warm place, work the rubber into an arched position since it doesn't want to naturally bend that way. It ships flat. Do the whole length and then really work the 1st 6" or a foot 3.pump some liquid soap into the channels of the threshold and also soap the starter end of the gasket, the one you just exercised into shape. Don't be afraid to use a lot of soap in the channels or on the gasket. If it's installed correctly the only way the gasket is coming out is to rip it out. 4.Try to keep the length of rubber aligned with the channels. At the threshold, using the now exercised end of the gasket, form an arch and push the very tips into the front and back channels. Start them close to the door jamb. Test to see if they're seated by gently prying on the end of the gasket on each channel. If they hold, they're in. Now slide the installed tips against the door jamb if they're not already there. 5.Here's where reading the instructions comes in handy. It says to push downward along the gasket toward the other end (or something like that). That does actually work, but instead I had spent a lot of time - I'm embarrassed to say how much time - trying to force the rubber into the channel using a variety of flat edge tools. However, pushing only works if you have enough rubber seated into the channel. I had about 4" seated when I was able to successfully push (hard!) with one hand while trying to keep an arch in the rubber and line it up with the channels ahead of the push. The soap comes in handy here since it allows your push hand to slide as you push. I had to push hard with the heel of my palm making sure to contact both edges of the gasket to engage the channels at the same time. Continue down the length of the gasket, checking as you go by attempting to gently lift the pushed edge out of the channel. If it stays in, keep going. It can be deceiving, looking like it's seated but it's not. Note: I was not able to push one side 1st and then the other which would have made sense. I think it only works to push down on center and both sides evenly as you go due to the way the edges align with the channels at the same time.So after a very frustrating time, it works quite well. I feel no cold air at the bottom of the door, only on the sides where a simple gasket will suffice.Moral of the story: lose the threshold completely and use a door sweep.