Your cart is empty.
Your cart is empty.The AC1068 Module is designed to connect your router/ switch to wired networking locations throughout the home. Eight front-mounted 110-IDC punch down terminals and RJ-45 connectors allow for easy configuration of the home network with patch panel simplicity. The network interface module is UL listed and exceeds TIA/EIA 568-C. 2 industry standards.
Brik
Reviewed in the United States on December 4, 2024
Most residential wiring is done tia-568B but this device is wired for A. Just be aware.
RS
Reviewed in the United States on October 25, 2024
Depending on your cabling may need to switch between T-56A or B during punch down.
Simsy
Reviewed in the United States on January 14, 2024
Good quality product. Works very well. Only comment is that it didn't fit my OnQ board exactly. The dimensions were all correct, but the tabs that you insert first were just a tad too thick. They would go in their holes, but they would bind up when you tried to hinge the board down. I had to use some sandpaper and round off those two tabs a little. Not much. Took maybe 10 seconds.
Adam V. Floyd
Reviewed in the United States on September 7, 2023
As many have noted the color code uses the European standard so you have to swap the green and orange wires. Otherwise, worked great. I like that the CAT mounts from the front which is way easier than from the back. Doesn't look as clean, but once the box is closed no one knows.
Mach1
Reviewed in the United States on August 3, 2021
I installed this in my daughter's new house. The builder installed an empty Legrand structured cabinet and pulled the wires (Cat5e and Coax) into it, but didn't terminate them. The installation of this interface module was was a bit tricky. It is awkward to install this module into the cabinet because the back of the cabinet is rather flimsy plastic. It took several minutes to get the pins lined up and snapped in, just right. Once that was done, punching down the wires was easy with a proper 110 punchdown tool.The module is only color coded for the older 568A wiring standard instead of the more modern 568B standard. The builder elected to terminate a handfulsome of the wires with the 568A standard, so I had to terminate them to this module with the 568A standard. I terminated the remainder of the bare wires left dangling out of the drywall in the various rooms with the 568B standard. Therefore, I had to use the 568B standard when I terminated those wires into this module. As long as you use the same standard on both ends of the cable, it will work fine. You just have to watch what you are doing and test each termination with a cable tester when you are done.Of course, the builder neglected to label any of the wires, so I had to trace each wire using a wire trace tool.Bottom line, this is not always as easy as it looks and you must do your homework when using one of these. Honestly, I have never used Legrand products before, but I would not choose their line of products for any home I was building. In this case, I had no choice.
Shane H.
Reviewed in the United States on August 19, 2021
I took a total gamble on this module, hoping that if I swapped it with the existing telecom module in the wiring panel that my wired ethernet ports throughout my home would function correctly. Anyways, after removing the old module, using a punch-down tool to terminate the existing wires to this new module, I was really hoping I did everything correctly.Turns out, I did, for the most part. After hooking up a an ethernet switch, I got my most desired ethernet port working in a the wall outlet downstairs. Success! And it was running at 500 Mbs (the speed I'm paying for). Another wall outlet port was also working, but only at 80 Mbs, so I'll have to re-check the wiring on that one, as it may be wired wrong at the wall (A vs. B).In any case, you just have to hope that the existing wiring infrastructure is good wherever you install this module, as there are some many variables that can affect speed / performance. One final note, this module fits perfectly in my existing OnQ panel box and the plastic tabs lined up to the holes, no problem. It was an exact swap of the old (non-functional) telecom module.
ankurbs
Reviewed in the United States on May 7, 2021
when i moved into my home, all the ethernet cables were "terminated" in the garage. after taking a closer look, i noticed they were not terminated, but in fact, just sitting in the legrand q box, with connectors on them. so, i have ethernet cables all coming to one spot, but one way to connect them to a switch. i tried adding connectors to the end, but gave up as i realized i am just not that handy. enter this this "switch." it clipped in directly to my legrad q box with no tools and the color code for ethernet wire is listed on which "port". i did have to buy a punch tool, but honestly, learning how to punch (5 min youtube video) was easier and cheaper than hiring someone. Once i was ready, it took me 20 min to strip, punch down, and test each "port". once that was done, i connected each one to a standard switch and boom....all my ethernet ports were active.it is made of plastic, so just careful when handling, but it was study enough to handle the punch down tool.
Rahim Ullah
Reviewed in the United States on April 27, 2020
Snapped right into an On-Q panel in a house built around 2002. All of the Cat5 jacks were wired as phone ports with regular Cat 5 cable, but fortunately they had also run Cat 5e cable to some of the ports (zip tied to the Cat 5 cable). I needed this to hook up unterminated Cat 5e cable in the wiring closet to an 8-port ethernet switch (I only needed 6 ports).
Recommended Products
$105.88
$ 42 .99 $42.99