Your cart is empty.
Your cart is empty.Designed for industrial, commercial and residential applications, the Intermatic T104P3 mechanical time switch has the highest motor load ratings in the industry. It provides direct 24 hour control of most loads. Applications include indoor/outdoor lighting, signs, pumps, filters, fans, pool heaters, electric fences and other electrical loads. These dependable time switches can handle loads up to 40 Amps per pole and allow for up to 12 ON/OFF operations per day. A manual override switch provides added convenience.
Jeffrey C
Reviewed in the United States on January 29, 2025
The timer was exactly what I had ordered the only issue I had was that the timer wasn’t the problem. They gave me no problem to return it. If I ever need another one I will certainly order from this company. They came through for me.
Bennett
Reviewed in the United States on January 12, 2025
Works as described
Luke
Reviewed in the United States on September 26, 2024
The media could not be loaded.
shopper
Reviewed in the United States on August 22, 2024
The TP104P3 performs as well the one it has replaced after 15 years of service. It’s a great value for the money, and I expect it to last as long as its predecessor. It’s also very easy to install.
Daniel Honick
Reviewed in the United States on October 29, 2024
Reliable product that is easy to install! A very good value!
Carolyn T.
Reviewed in the United States on October 10, 2024
Replaced original timer unit. So far so good!
don
Reviewed in the United States on August 7, 2022
The unit and mechanism seemed fine and worked well for about nine months. The switch mechanism is mechanical. Gears cause a calibrated aluminum disk to rotate once every 24 hours. The on and off switches are clips mounted to the edge of the disk with thumbscrews. The back sides of the clips trip the switch mechanism. The switch mechanism was so stiff it eventually caused the clips to slip. When I tightened the thumbscrews with pliers, the clips stopped slipping, but eventually the entire disk started slipping because the switch mechanism needed too much force to operate. The mechanism is fastened inside the plastic box and I haven't tried to take out the mechanism for fear of breaking the fasteners, so can't see behind the disk very well, but I can see it turns by gears. So I assume the gears are stripped, because when the disk meets a clip, the disk stops rotating. I'm now looking for an electronic replacement for this unit and recommend readers consider the same.
Joe Miuccio
Reviewed in Canada on January 22, 2016
Great product and works perfectly. I'm using it for a Pool pump and I've had no issues with over a year in use.
Robert Steffen
Reviewed in the United States on August 4, 2015
Interesting problem solved. My pump shorted out (impeller went bad and leaked) and this caused a huge flash inside the intermatic control box when I turned on the pump manually with the switch in the intermatic box. I had to replace the pump, but the intermatic control was stuck in the always on mode due to the power surge. I then just used the breaker in the breaker box to turn the pump on and off. Then one day, nothing. So I order this exact replacement and did the swap myself. Very easy to do, just be sure you kill the power and use a voltmeter to ensure no live wires. Went to turn on the pump, it dd not work. I checked each connection and each had 110 volts. I puzzled over this for 2 days, connecting and reconnecting and still nothing. If you look at the internal control module, going from right to left, I use the first 4 of the connections, not the 5th, and each showed 110 volts. I was starting to think that the new one was defective, even the timer dial was not operating. I finally went to my local pool supply store and spoke with them. I brought the old timer and showed them how I had the wires connected and what voltage I was seeing. They told me my breaker had either become weak or gone bad, even though I was still seeing voltage. The said on the 1st and 3rd screw connector, I should see 110 volts, on the 2nd and 4th screw connector, I should see 220 volts. I thought they were crazy, but they were correct. I purchased a new breaker, swapped it and and everything started to work perfectly. Hope this information is useful to someone.
Recommended Products
$18.91
$ 7 .99 $7.99