Shopping Cart

Your cart is empty.

Your cart is empty.

G GreatCircleUSA Wood Chipper Shredder Mulcher Replacement Blades for LCE01

4.8 (8) Write Review
Free shipping on orders over $29.99

$29.99

$ 13 .99 $13.99

In Stock
  • DETAILED SPECIFICATIONS - Our Wood Chipper Blades are only designed specifically for the LCE01 GreatCircle Wood Chipper. The blades have a dimension of 3"L (76.5mm) x 1.3"W (34mm) (or 1-11/32) x 0.19"H (5mm) (13/64). Each blade weighs 0.22lbs / 3.5 ounces. These blades have a Center-to-Center length of 1.5", an Inner bolt diameter of Ø9mm & Outer bolt edge is Ø18mm
  • EFFICIENT RESILIENT DESIGN - These Chipper blades are precision manufactured to be mounted with (2) M8x25 bolts holding each blade into place (*Note: the bolts are not flat but slanted at 10.9 degrees). We chose a very strong & long lasting CR12Mov Steel material for our blades, providing excellent longevity of use. Our blade edges sit at a 39.5 degree, for optimal chipping capability
  • SAFETY & PROPER USE - We always recommend that users always wear hand & eye protection when operating any machinery/equipment, for your safety. Our blades surfaces are oiled to provide anti-rust capability & shelf-life. These blades are for Chipping, Shredding & Mulching of wood & natural shrub, theses blades are NOT for metal, rock, cement or any other hard surface materials/debris


Product Description

The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked.

Ken
Reviewed in the United States on August 2, 2024
It fit my chipper/shredder
Kindle Customer
Reviewed in the United States on December 22, 2024
While this result came back off a query for Yard Machines chipper blades, they do not fit the 10 hp unit. The bolt spacing is too narrow by a 1/4".
Customer
Reviewed in the United States on December 17, 2024
They came on time and are sharp.
Stuart
Reviewed in the United States on June 29, 2023
I installed the 2 blades and it was simple and quick. Worked great. I then sharpened the old blades and will keep them as backups
Customer
Reviewed in the United States on October 28, 2023
I pulled up the Great Circle Wood Chipper order receipt I bought two years ago. The recommended blades had two screw holes. However, when I went to install the blades, I noticed that my original GC Wood Chipper's blades had three screw holes and not two. Be careful not to follow the recommended blade parts and check your machine first to ensure the correct blade parts.
john
Reviewed in the United States on September 14, 2022
Wood chipping
Cardoc
Reviewed in the United States on October 5, 2022
Great value. They fit my Simplicity 5/14 with just a little grinding and new bolts. Simplicity is no longer made so what's left in stock is super expensive. Works great now.
Retro Piano Guy
Reviewed in the United States on August 20, 2021
Direct replacement intended for the LCE01 chipper that I bought earlier this year. It made a huge difference! Before the replacement, I had to push most branches into the chute, and they would vibrate a lot and sometimes rattle a lot. Now the machine pulls the branch in, sometimes I don't need to push it at all. Also much less vibration and almost no rattling.Installation was 45 minutes. You have to remove a lot of 1/2 inch bolts to get access to both front and back of the blades. Once the hopper is off, the machine wants to tip over, so I put some stone blocks under it for balance. The blades are connected with an alan wrench on front and lock washer / bolt on back. No need to make it extremely tight. Just give it a good tug so the lock washer smashes a bit, and that should do it.