Your cart is empty.
Your cart is empty.Product Description
Description：
Tongue and Groove Router Bits Set is used to produce shaker rails and door frames for cabinet doors, floors, paneling and many other projects.The Router Bit Set can make perfect tongues or grooves and make them fit perfectly.The gap between the grooves can be adjusted to increase the fit by using the trim spacers (thickness: 0.2mm, 0.5mm) included with the kit.
Product Description:
Tongue and Groove Router Bits Set
Create a tongue and groove for a perfect connection between two materials.
Smooth Operation
Each bit is powder coated for an extra layer of protection.Enclosed bearing roller makes for easy alignment for a dreamless operation.
Advanced Materials
C3 Tungsten carbide blade provides a clean and accurated cut.
Specification:
- C3 Tungsten Carbide
- 1/4 Inch Shank
- 3 Teeth T Shape
- Max 16000 RPM
- 1x Tongue Router Bit
- 1x Groove Router Bit
- 2x Adjustment Washer (0.2mm, 0.5mm)
Instructions for use :
- Always ensure that the safety measures prescribed by the machine are enabled.
- Make sure to use it on a router machine for which the product is applicable.
- Before the product is received for use, check the drill bit for cracks or chips, if there is any problem, you can leave a message to Fivepears,we provide perfect after-sales service
- Max. Rpm in 16000！！
- Clamping to at least the K mark！！
Quality Construction
C3 Tungsten carbide blade provides a clean and accurated cut.1/4 inch shank also fits most routers for easy installation and safe use.
Smooth Operation
Each bit is powder coated for an extra layer of protection. This allows you to use multiple times.Enclosed bearing roller makes for easy alignment for a dreamless operation.
Scope of application
For cut wood,MDF,particle board, plywood,etc.
Advanced Materials
Fivepears products are made of C3 hard tungsten steel and 45# carbon steel for durability.
Clean Cutting
Sharp cutting edges made of Fivepears C3 grade carbide for smooth cuts
Shear Angle Design
Fivepears' shear angle design, smooth mirror surface helps chip removal speed
Professional bearing
A good bearing can often do more with less, Fivepears’s bearing can help you control the cutting speed and guide you to cut in the right direction.
Jeffery board cutter
Reviewed in the United States on February 28, 2025
Five Pears always good products!
Stewart Poitier Fontenelle
Reviewed in the United States on February 11, 2025
It works exactly the way I expected
Gene Morin
Reviewed in the United States on January 29, 2025
work very nice
Frank W
Reviewed in the United States on June 24, 2024
cutting heads differ from american cuts. They are not the same as the mill cuts the wood.
RM
Reviewed in Canada on March 4, 2024
Bought these router bits twice.First time i had bad cuts for the groove (see pics). Tried again and 2nd time the cuts were accurate but the groove bit broke on the shaft and went flying off at a high speed. I was routing pine boards and it should never have happened. Poor quality. I guess you get what you pay for.
CKGurr
Reviewed in the United States on March 14, 2024
I got a set of these to make some cabinet doors. They’re are sharp and sturdy and would earn 5 stars. BUT they are not well balanced and vibrant horribly (both bits). I believe that they would destroy the bearings on my new router. Too bad because they would be great l.
stopblock
Reviewed in the United States on December 5, 2024
Arrived on time & packaged well. Dimensions of cuts were perfect for 3/4 plywood. Made nice clean cuts.
thomas
Reviewed in the United States on November 9, 2024
Works amazing and cuts accurately
Andy Mitchell
Reviewed in the United States on November 20, 2024
Really inexpensive for a set of router bits. Works great. Just feed gently - that's a lot of bite for a 1/4" shaft.
Catherine
Reviewed in Canada on November 17, 2024
Bien
Bill Schuster
Reviewed in Canada on August 18, 2023
worked well with cutting grooves.easy set up
andrewthealleycat
Reviewed in Canada on May 18, 2023
Good quality carbide. Use lower RPM for this bit and lubricate the bearing with oil.
G
Reviewed in Canada on October 2, 2022
This is a great set. I did read reviews about the shaft bending, so when I got mine I figured out how long it actually needed to be and then cut the shaft off to the length I needed. At the end I only have about 1/2” of shaft out of my collet and haven’t had any issues with it. So far I hav done about 1000sqft of 6” flooring and have no complaints. Joints are a good fit and it make a clean cut.
Recommended Products