Your cart is empty.
Your cart is empty.Reese front mounted hitch receivers allow a variety of accessories to be mounted on the front of trucks, vans, or SUV's to perform tasks that make outdoor adventures and activities easier and more fun. Accessories are easily interchanged, so the receiver is a practical and versatile addition to sporting and work vehicles. All front mount receivers have a 2\" square receiver tube opening and all attachments are j-pin ready. Front mounted receivers offer a secure and useful attachment point and offer 9000 lbs. Of line pull and 500 lbs. Vertical load. The METALSHIELD protective coating process is a three step finish consisting of a rust inhibiting primer, dipped e-coat electrostatic coating to insure total finish coverage and finally an outer powder coat finish for durability. The METALSHIELD process is an OEM compatible finish providing the best corrosion protection over brands that use only powder coat on their products.
Chris T
Reviewed in the United States on July 12, 2024
Did not fit my 2016 75th Anniversary Jeep Wrangler as advertised
Me12
Reviewed in the United States on December 24, 2024
Set up easy
Ragnar
Reviewed in Canada on January 12, 2024
Nice, well built, hitch. Really easy to install, fit my 2010 Rubicon with no drilling.The hardest thing about the install was removing the plastic splash guard (AIR DAM) below the bumper.There is a good install video on YouTube.
DeAn Dawson
Reviewed in the United States on March 4, 2023
I was worried it wouldn’t work with my aftermarket front bumper but it tucked up really good. IT’s slightly short (for ease of instinctively) so don’t tighten one side until you have all 4 bolts snug. Has two forward bolts that wouldn’t work with my bumper but it is strong without them.
alexander h.
Reviewed in the United States on April 20, 2023
Front Receiver fit factory holes in frame and shims supplied made a tight installation. Instructions only show a small picture of what has to be cut out of air dam . Took longer to cut hole close to receiver in air dam and make holes for new bumper bolts without butchering air dam.Had new plastic push pins to hold air dam securely. Only the 2" front of receiver opening protrudes through the air dam and does not interfere with the license plate'.
Robert
Reviewed in the United States on September 4, 2020
Easy to install, holds my cooler rack on my JK’
Keyone user
Reviewed in Canada on August 29, 2020
Not enough shims to get a good tight fit
Jeff
Reviewed in the United States on January 25, 2020
So, been waiting a long time, finally found this, spent all day, fab'd to a push bar for a 02 ford ranger. Oh yeah, Hooks, And a winch... TOP GUN! didn't spend 400 bucks! Spent 100 bucks. I am fine with that, plus my time. That is always the case.
danny dube
Reviewed in Canada on October 10, 2019
nedd to put spacer on one side, overhall easy to install
Customer
Reviewed in the United States on July 18, 2018
Terrible weld quality. Needed to grind weld spatter and over weld away from bolt holes so washers would sit flat. Needed to elongate mounting hole in bumper by 1/4" to fit. Needed to grind open bolt hole in frame to fit bolt. Overall placement of critical mounting holes was poor. Overall length was too short. Needed to make shims to keep from distorting Jeep frame when tightening bolts. I wouldn't put much load on this hitch. I only intend to use it for a front mount basket. Skill recommended for install: Good Fabrication and Fitting Skills.
Rian Buchanan
Reviewed in Canada on April 30, 2018
This literally took me 20 minutes to install on my '07 Jeep Wrangler. I think I spent longer reading the instructions the day before the install. Now, I already had the bumper off, as I installed this while putting in a rebuilt engine, so it will take longer to gain access if you have a factory bumper. The tabbed nuts may be one of the best inventions ever; I wish more manufacturers used them. I thought it was a little odd that it doesn't sit exactly between the frame, needing spacers on only one side, but it works, and that is what's important.
MaddyIce
Reviewed in the United States on March 25, 2017
The package was torn open at one of the corners and two handle nuts were missing. I replaced them with regular nuts from the hardware store, which took a lot of work to install. The instructions were good, and everyone's comments on here seem accurate. I had to widen the hole in the drivers side, per the instructions. I did this pretty easily with a Dremel. The drivers sound mount doesn't fit flush, but it does touch once you torque it down. It was too close for me to shim it, so I didn't have much of a choice. The powder coat is probably the worst I've seen on any product; it was chipped or peeled off in several spots. I was glad to see the instructions include the 9,000 lb capacity and winch instructions. It actually arrived with a Drawtite sticker, not Reese, but I kind of expected that because they are the same part number. The price was good, but looking back I might have considered a different brand. I was partial to this one because the reinforcement plate is on top instead of under side of the hitch, which I think looks better.
Recommended Products
$228.38
$ 99 .00 $99.00