Your cart is empty.
Your cart is empty.Product Description
This 4-channel K Thermocouple SD Card Logger is the best tool for multiple measurements. It can record temperature changes by setting up data logging with no software required and no memory limit. The unit can be used by either wallmount or handheld.
Includes a large backlit LCD screen (104 x 47mm) for easy readability, a real-time clock, and programmable HIGH/LOW alarm limits with beeper and LED indications. With a low-battery indicator and 20-minute auto power-off for energy conservation.
Grandpa
Reviewed in the United States on December 22, 2024
Device works fine for recording temperatures but the calendar resets to 1/1/2014 or some incorrect date sporadically when powered by batteries. When AC adapter is used this has not happened so far. The time remains correct so downloaded data can be corrected in the spreadsheet. Batteries were replaced for overnight run but calendar still reset. Outside temperature was down to 18 F and battery voltages were down to about 1.28 volts at the end of the 18 hour logging period. Battery drain may be culprit so running an extension cord and using AC adapter may be necessary if practical (not practical for my situation). Where AC power not practical i may need to create battery pack with plug using D cells.
Blanca Salinas
Reviewed in Mexico on January 2, 2024
Producto de buena calidad, tal cual la descripción 👍🏻
Steven Emanuel
Reviewed in the United States on July 29, 2023
Briefly:I purchased this to log temperature data, every five minutes, just the temperatures. This is simple enough, I am not asking too much. But this device was not writing data to the SD Card as it was supposed to. So, I sent a message to the manufacturer, but they just basically told me to "read the manual". No problem, I read technical manuals, I write them, I design products that have manuals, I know the drill. As it turns out, I had already read and re-read in detail their manual before contacting them, and I did not need them to tell me how to set up their device. I had already done so. The problem was that they did not listen to the problem, so let me state it again clearly:THE DEVICE IS SET UP PROPERLY.THE SD Card has been properly formattedIT TAKES DATA BUT ONLY APPENDS THE DATA TO THE SD Card FOR A WHILE. This could be a few hours, or just a few minutes. THEN DATA LOGGING STOPS RANDOMLY.For example, here is a set of data that was supposed to last a full day:MN/AT date time int 1ch 2ch 3ch 4ch unitAT 2023-07-17 17:11:12 5m 41.6 43.1 30.5 CAT 2023-07-17 17:16:12 5m 41.6 43.0 31.4 CAT 2023-07-17 17:21:12 5m 41.6 42.9 31.4 CAT 2023-07-17 17:26:12 5m 41.6 42.9 31.9 CAT 2023-07-17 17:31:12 5m 40.9 42.2 31.3 CAT 2023-07-17 17:36:12 5m 40.2 41.2 31.3 CAT 2023-07-17 17:41:12 5m 40.1 41.2 31.3 CAT 2023-07-17 17:46:12 5m 39.1 40.1 30.6 CAT 2023-07-17 17:51:12 5m 37.7 38.6 29.3 CAT 2023-07-17 17:56:12 5m 36.9 37.9 29.3 CNOTICE that it is set up correctly and taking data every 5 minutes, but then stops logging after only 10 time points.Infuriatingly, if you repeat this, exactly, without changing any settings, it will log for example: 3 time points, then 2454 points when you restart it, then 12, then a few hundred... and on and on like that, just stopping randomly, with random sampling periods each time before it quits.So, the company can either send me another one THAT THEY HAVE TESTED AND THAT WORKS PROPERLY AS ADVERTISED, AT THEIR EXPENSE, or I will just take the loss and advise everyone:>>>>>>>>>>>>>>>>>>>>> DO NOT BUY THIS PRODUCT
Mitch Joseph
Reviewed in the United States on May 25, 2023
The unit is a good value, providing 4 inputs and data logging. The unit is simple, but the operation in not very intuitive. The unit has to be dismounted to gain access to the SD card.
Chris Jones
Reviewed in the United Kingdom on November 12, 2021
Easy to use, captures data and is very easy to load to Excel for analysis.
Teccor72
Reviewed in Italy on November 25, 2020
Il prodotto corrisponde perfettamente alla descrizione e funziona benissimo, era dotato di una SD interna per il salvataggio dei log dati, estrarre i dati è facilissimo e con le tabelle in exel si fanno tutte le analisi del caso .Unica cosa fondamentale se si fanno rilevazioni di ore, lo strumento NON ha un suo alimentatore ma solo le pile, quindi bisogna fare attenzione alla durata oppure comprarne uno.
Happy Shopper
Reviewed in the United States on August 5, 2019
I'm using this to monitor the efficiency of my boiler system. The 4-channels are good. I tested in an Ice bath and boiling water, Using the offset feature, I was able to calibrate all the channels within a couple of tenths of a degree of each other well within the advertised specification. I also compared it to my fluke meter. The unit generates a CSV file when logging. I was able to take the generated CVS file and import to OpenOffice to plot the temperatures in and out of the boiler and each zone to calculate the thermal energy being used by each zone. I was using this to adjust the water flow speed to ensure that the water spent enough time in the pipe circulating in each zone to properly heat my floor.Pros: Uses standard k-type thermal couplers. The display is easy to read each channels temp Uses a standard power supply 9V 1.5A Center Positive 5.5mm X 2.1mm connector Logs to a CSV file, configurable sample rateCons: The display turns off when logging mode is operational While you can figure out the manual, its hard to read poorly translated English The probes that come with the unit are very short (glad the K-type probes are cheap)All in All, I do recommend this unit.
Jose Javier Nagore
Reviewed in Spain on July 13, 2019
Buen aparato de excelente calidad y buen precio
Samsmom
Reviewed in the United States on June 20, 2018
Works great. Temperatures seem to be accurate. Logging to SD card works very well. In made some nice charts in Excel with the data I captured. Operation is not intuitive but the included manual explains what you need to know.
WaggRnch1
Reviewed in the United States on March 28, 2018
Works great for displaying and saving (to the included 8GB SDHC memory card) four(4) channels of thermocouple temperature data. Then you need a USB SD-card reader (or some other mechanism) to get the data into your PC. No special software required. The resulting text files are easy to read, and include date, time, and 4 channels of temperature data. Having the 2x2 temperature display, instead of a 1x4 list, really helped in our application. As others have indicated, the readings tend to jump around a bit (perhaps up/down 3 degrees C) in the presence of electrical devices, a design defect which ought to be corrected. Others have complained about the instructions included, perhaps they have been upgraded, they weren't perfect but they were pretty good. We were up and running in short order, and this device paid for itself on the first day of usage. You may as well also purchase "9V 1.5A AC/DC Power Adapter for Arduino, Tbuymax UL Listed Center Positive 5.5mm x 2.1mm Power Supply..." to save on batteries and enable long-period usage. Overall a good product deserving of your consideration.
Rookemonster
Reviewed in the United Kingdom on November 26, 2018
Great piece of equipment, good features, works exactly as the ad says, runs on batteries or optional mains adaptor which isn't included.
Eric M
Reviewed in the United States on July 27, 2016
I'm using to record temps in my burnout kiln to figure out what is going on in my flasks. I bought some fiberglass insulated thermocouples so I can track flasks as they go up to 1350F. It tracks great, it's accurate (I always have a control), and outputs an easy to use flat file.I would recommend this and I will actually probably buy another one. I went from 0 to 4 inputs and now I kinda want 8 :P
Recommended Products