Your cart is empty.
Your cart is empty.Product Description
Features
Extra-low motor noise offers excellent quietness
Anti-Resonance, provides optimum torque and nulls mid-range instability
Self-test and auto-configuration technology ,offers optimunm responses with different motors
Microstep Resolutions Programmable
Power Voltagge up to 80VAC / 100 VDC
Output Current Programmable(2.0~6.0A)
Pulse Input Frequency up to 200KHz
Automatic Idle-current Reduction
Supports PUL/DIR and CW/CCW Modes
Mechanical Specifications (unit :mm /inch）
Connections
Pin Assignment and Description
P2 Function (DM860S)
+VDC : Power Supply, 18~50 VDC, Including Voltage Fluctuation and EMF Voltage
GND : Power Ground
U: Motor Phase U ; V :Motor Phase U W : Motor Phase W
P1 Function (DM860S)
Edgar Juárez Cuevas
Reviewed in Mexico on February 6, 2024
producto bueno, confiable, recomendable 100%
Pierre Dionne
Reviewed in Canada on May 31, 2023
Assez fiable !
Mike L.
Reviewed in the United States on September 9, 2021
Came as a silver colored SmartRayC, not the Cloudray described. But specs on the case are the same right down to the "Valtage" misspelling. Ran a 4.2A NEMA 23 motor with a 60V power supply. Driver is well ventilated in and indoor setting. Worked well initially, but after 5 months and about 40 hours run time, began to lock up occasionally or skip pulses repeatedly. Replaced it with higher quality driver and problems are gone. Would not buy it again.
SuperSpill
Reviewed in the United Kingdom on January 7, 2021
This dropped into my laser cutter and worked perfectly (after adjusting the jumper switches) I had bought 5 other cheaper DM542's which all caused a misalignment issue as they gradually lost steps. Definitely recommend spending the relatively small amount extra to get cloudray quality.
Dr.T.
Reviewed in the United States on December 2, 2020
Exactly what you want for nema 23 motors. Those tb6600 drivers are junk.
Alexander Manilton
Reviewed in the United States on November 23, 2020
I was shocked. Yeah, they will run hot since you're pumping constant current at all times, but oh my god, finally a simple controller to replace a $2k servo drive.
Bickel Alfred
Reviewed in Germany on November 11, 2020
Funktioniert bestens auf meinem Berger und Lahr Schrittmotor. Habe aber noch nicht alles austesten können.
Angel
Reviewed in Spain on January 19, 2020
No consigo regular la velocidad del motor cambiando la frecuencia de los pulsos en +Pul -Pul, el motor gira pero siempre a la misma velocidad.
John R.
Reviewed in the United States on June 1, 2019
48 volt capability was important to me
jdally
Reviewed in the United States on February 7, 2019
Product as advertised
Anthony N.
Reviewed in the United States on December 11, 2018
This is the most cost effective stepper driver I've found that can handle higher voltages. On my machine, it outperformed $180 drives. It doesn't require any software tuning to take full advantage of the driver, so it was very simple to install.
Customer
Reviewed in the United States on November 4, 2018
The most important thing about this driver is how well it drives a stepper motor. There is no noise as a result of no vibration even when I set the amperage that would overdrive the motor. It is also very convenient that the rms amperage is shown on the dip switch table. These drivers are so smooth and quiet they are really worth the additional money. I have replaced all of my TB6600 with these. The TB6600 are really not good for a series of reasons. I definitely highly recommend this driver.
Doug Adams
Reviewed in the United States on November 29, 2018
Has performed very well. Using to drive a large stepper. No problems so far using a 48 vdc supply on a high torque stepper. Control is great.
Recommended Products