Your cart is empty.
Your cart is empty.Product Description
TECPEL CA-60 DC/AC Clamp Transmitter
The CA-60 DC/AC current hook is mainly used to convert the measured current into a voltage output mode, so that the equipment in the later stage can obtain the current measurement value. CA-60 can be used with a digital meter or oscilloscope.
Measurement Specification
- Measuring Range : 0~60A
- Clamp Caliber : 9mm (3/8“)
- Signal Output : 1 mV / 10mA or 1 mV / 100mA
- DC Accurary : ±1.5%
- AC Accurary : ±2.0% (40~2K Hz) / ±4.0% (2K~10K Hz)
- Frequency Response : 20K Hz
Alwin Campbell
Reviewed in the United States on March 8, 2025
Works greay
Vincent M. Peck
Reviewed in the United States on March 31, 2024
The first one I bought was returned to Amazons 30-day window for a broken lead. The 2nd one quit working after 8 months. Beware: there is no manufacture's warranty on them. After contacting the company, they told me to just buy another one! I told them I've wasted enough $ with them, so I won't be doing that again.
WALTER W.
Reviewed in the United States on May 6, 2023
You have to zero it Al lot. It’s not as small As it looked I was not able to use it where I needed. What is also difficult to interpret as the scales are really odd ball.
John Banister
Reviewed in the United States on August 27, 2022
The product itself works however it will not fit all DVOMs. I used it with my ET826 graphical multimeter and the banana plugs on the clamp transmitter probe were very loose and would not read when I tested it. The banana plugs did work on my Hantek DSO1200 oscilloscope. I use the graphical multimeter in the field as a mechanic and if the plugs are loose or do not make contact to the meter, the probe is useless. I had to return this item.
Nelson
Reviewed in the United States on June 15, 2022
I bought it because most amp clamps only measure alternating current. This one measures both AC and DC without interrupting the circuit. I use it with a trusty old Fluke 27FM multimeter.
howard patkotak
Reviewed in the United States on May 3, 2022
Works good!
Franklin D. C.
Reviewed in the United States on September 17, 2021
This is how the day started. Three guys 1 semi ??? It’s got to be the fuel pump (test,test,test,test) snap on tools , multi meters , volts are there and this guy says my clamp reads lower volts than your let’s give it a shot …. BOOM on the scope a super low profile waveform! Both the other guys ordered one before the lift pump was delivered. Low amps are hard to find this amp makes a pretty picture for you…..
Jerry
Reviewed in the United States on September 16, 2021
Overall I am happy with the device. However, it is somewhat difficult to get a correct measurement for low levels of direct current because the "Zero" settings does not hold for very long. You may need to Zero sensor and quickly read the current several times to and average the readings for best accuracy. I find that for low currents I can clamp the probe around the current carrying wire, Zero the sensor, quickly open the jaws to get get the wire out, then close the jaws and observe the reading. The resulting reading will show a current value (ignore the direction indicated ty + or +) that has a lower effect from the Zero drift. All DC clamp-on current sensors have the Zero drift problem; it might be a little less on more expensive devices.
nhon
Reviewed in Canada on November 10, 2020
Clamp-On probe works fine. With Amazon, you never know where the items you are purchasing are coming from. This probe came from Taiwan so there was a significant tax and customs charge, which I wasn't expecting, and of course, Amazon will never tell you that.
Recommended Products