Your cart is empty.
Your cart is empty. đQuel type de bouteille de rĂ©frigĂ©rant devez-vous charger ?
Ce tuyau de charge de rĂ©frigĂ©rant R134A convient aux bouteilles de rĂ©frigĂ©rant produites aux Ătats-Unis et en Europe avec un filetage 1/2, ce qui en fait un outil polyvalent et pratique pour les besoins de rĂ©frigĂ©rant de votre vĂ©hicule.
đđđ Maximisez les performances, rechargez facilement le rĂ©frigĂ©rant de votre vĂ©hicule
đ đ đVous voulez une vie meilleure ? Voici les avantages dont vous avez absolument besoin :
1. Restez au frais et en contrÎle grùce à notre tuyau de charge de réfrigérant R134A doté d'une jauge intégrée pour une surveillance facile - plus de devinettes, juste des performances puissantes.
2. Dites adieu aux tuyaux fragiles - notre tuyau de charge de réfrigérant R134A est conçu pour durer avec une construction solide et une endurance maximale, fournissant des résultats fiables à chaque fois.
3. PrĂ©parez-vous Ă faciliter l'entretien du vĂ©hicule avec notre tuyau de charge de rĂ©frigĂ©rant R134A, conçu pour une utilisation facile et pratique et adaptĂ© aux bouteilles de rĂ©frigĂ©rant produites aux Ătats-Unis et en Europe.
Spécification :
Type : tuyau de chargement de réfrigérant de voiture
Matériau : Métal et plastique
Sujet : 1/2
DiamÚtre intérieur du fil : 1,14 cm/0,45 pouce
DiamÚtre intérieur du filetage cÎté bas : 1,3 cm/0,51 pouce
Pression du tuyau : 600-3000PSI
ManomĂštre : 100PSI
DiamĂštre de la jauge : 5,1 cm / 2"
Taille de l'article : environ 50,5 cm / 19,8 â(L)
Poids net : 179 g / 6,3 oz
Forfait :
1 * tuyau de chargement de réfrigérant de voiture
Logan
Reviewed in the United States on March 9, 2025
Installed on my 02 c5z, perfect rumble and no drone down the highway
Customer
Reviewed in the United States on June 15, 2024
Perfect fit.
Tim Moultrie
Reviewed in the United States on March 18, 2024
Fairly easy to install once the vehicle is off the ground. They are louder than OEM but they donât really have the sound I was looking for. I wanted more of a deep and distinctive sound rather than a bunched together noise. Of course I am a little older. I put them on my 2004 Corvette with the 350 engine. I liked the sound I got out of my 66 Chev Impala SS with the 327 and glass packs. So there you go.
Michael A. Bower Jr
Reviewed in the United States on February 7, 2024
All I can say is WOW. This really woke up my 01 C5 from the stock exhaust. I combined this with the borla x-pipe and man does this make the car sound so good. Well worth the price. Had a shop install everything since I don't have the tools to do it myself. I debated going with the dual tips vs the quad, but I didn't want to ruin the look too much so I pulled the trigger on these instead and don't regret it one bit. Gets nice and loud when getting on it and has some slight but quiet rumble on idle or cruising at highway speeds, so the best of both worlds!
c5
Reviewed in the United States on December 3, 2023
Borla is An American made product. I have had negative experiences with offshore products and will only use made in USA on my c5 corvette. Borla is top quality. They sound great with no annoying droning at cruise speeds.
Kirby
Reviewed in the United States on December 22, 2023
This system was very easy to install and was exactly the sound I was looking for. I have the base model 2000 C5 with stock manifolds and H-pipe, this system compliments this setup with nothing else needed. I only have quick jacks (great product also for Vettes) so I couldn't get the car high enough to get the stock mufflers off without cutting the over the axle pipes. The new Borla system went on and went together with no issues at all. Just pay attention to a few steps that are not listed in the instructions. Very simple and easy to do if you pay attention. VERY SATISFIED with this system and both the look and the sound!
Charles Merritt
Reviewed in the United States on November 16, 2023
It's a Borla, which means it is not cheap. Is a good price here. Installing is a PITA, you're gonna need to get the backside of the car WAY up. It's not that the Borla is that bad, getting the old one out without cutting it is a real treat. I HIGHLY suggest having a shop do it unless you have a lift. The sound is beautiful, Vette sounds like it should now.
Carin Timmins
Reviewed in the United States on June 30, 2020
Install required the car to be on a lift, I could not manipulate the stock Z06 exhaust out on the jack. It required nearly 3 feet of clearance to angle the exhaust straight down to get the flange side out from above the axle. Install was easy on the lift. Took some tweaking to get the tips all symmetric. SOUND is mellow. Nice low roar. I was expecting much more aggressive, louder sound based off Borla, aggressive sound meter. No drone and not annoying at all. This is how the car should have sounded from Chevrolet.
Recommended Products
$736.00
$ 99 .00 $99.00