Your cart is empty.
Your cart is empty.
- Measures current range of DC 0-50A.
- Clear and easy to read scale and a button for fine tuning the dial.
Bruce Sayre
Reviewed in the United States on August 24, 2024
Used to replace broken meter in an older battery charger. Slight modification to mounting opening. Works as it was intended.
Robert W. Bacon Jr.
Reviewed in the United States on December 25, 2024
Very good setup, works great for my current measurements. Good cost and fast shipping. Happy with purchase.
Victor C
Reviewed in the United States on April 7, 2024
I have now a mix of four of this brand's meters and they are all nicely done for a budget price.
House Builder
Reviewed in Canada on July 3, 2023
The first thing that you need to know is how to properly connect an ammeter, which is in parallel with the shunt. Connect the positive lead from the battery to one end of the shunt. Connect the other end of the shunt to the load, i.e., the appliance, that you are powering. At this stage your appliance will work like before. The only difference is that current flows through the shunt instead of directly through the wire. Now, connect the meter to the shunt. The back of the meter is marked plus and minus. Connect the plus post to the same side of the shunt to which you connected the positive lead in the first step. Then, connect the minus post to the other end of the shunt, where you connected the wire carrying current in step two. If you are careless and connect the leads the other way around the needle may swing the wrong way and damage the meter. The diagram is for a voltmeter and an ammeter, as I installed both to monitor output from my solar array. The meter seems to be good quality with an attractive appearance and is easy to read. Also, easy to install. It is easier and more accurate if you first make a paper template and then use it to properly position the meter and drill the holes.
Bob F
Reviewed in the United States on July 30, 2022
Got this for an atx power supply build. Not much to say... It works like it should, built well, and accurate. Came with the shunt as well. They didnt send the 4" of wire required, but also forgot to include the dancing girls. Go figure. Other than that, great product from a great merchant.
Gabriel M.
Reviewed in Mexico on September 19, 2021
Mala calidad del grabado de números, se borran al limpiarlos. No recomiendo
RTM
Reviewed in the United States on August 22, 2021
The meter and shunt were very easy to wire together. The meter is easy to read and has been installed.
tacksman
Reviewed in the United States on March 13, 2021
Made a homemade shunt tester for small engines and testing the charging systems. Seems to work just fine. Thanks.
Johanne Beaudoin
Reviewed in Canada on October 26, 2021
très satisfait et très bon achat.Merci a votre équipe
Lorin
Reviewed in the United States on December 31, 2019
Used to measure the 12v current from my SUV hitch connector to the trailer.Works nicely and seems accurate enough for my use.Make sure to use heavy gauge wire. 10AWG is what I used. That lessens the voltage drop and provide a little more current measuring accuracy.
Michel Gauthier
Reviewed in Canada on December 3, 2019
mesurer mes ampères que ma plaque solaire fournit a mes batteries.
JP Morency
Reviewed in Canada on December 15, 2019
Excellent value for the price.
Signal_Ridge
Reviewed in the United States on March 23, 2018
These panel meters were tested and found to function properly. The display is clear and easy to read. The panel meters are plastic encased and lightweight. Our friends in China at Baomain have once again produced a quality product at an affordable price. These meters arrived along with two volt meters from Baomain and the packaging was better than I see from most domestic shippers. Four outer layer of bubble wrap invidually boxed inside a larger box with foam and even foam inside the individual meter boxes. These came direct from China so allow some time for delivery which includes delay at our USPS International Sorting Centers.
Recommended Products
