Your cart is empty.
Your cart is empty.No one enjoys scrubbing off stubborn, dried-up bug guts after a long road trip. That’s where the Bugflector II comes in. The high-profile wrap-around design provides maximum protection from all bugs, big and small, while its off-the-hood design allows for easy cleaning and waxing. Made from durable impact-resistant acrylic, the Bugflector II can stand up to everything from car washes and bugs to the wear and tear of daily driving or going off-road. Custom-molded to fit your vehicle’s exact year, make, and model and contoured to fit the curves of your hood. Available in dark smoke finish and proudly made in the USA with global materials
anselmo arellano
Reviewed in the United States on February 14, 2025
Looks great on my vehicle. Was easy to install
Medic8
Reviewed in Canada on September 19, 2024
This was a replacement for a previous AVS product that used 3M tape & had lasted 5 years, failing because the 3M tape failed. This deflector mounts directly to the underside of the hood using four screws ( included) & is quite sturdy but did not come with any mounting instructions. Install took about 5 minutes. Was delivered within 2 days.
Lynn Bowman
Reviewed in Canada on August 15, 2024
Very east to install
David N.
Reviewed in the United States on August 10, 2024
Fits like a glove. Looks good!
Scott Pepino
Reviewed in the United States on June 27, 2024
I can’t do anything. And I installed this in 10 minutes alone. Looks great. Well secured with the screws that are lined up perfectly with the already existing holes. Perfect.
Olivier Couture
Reviewed in Canada on August 2, 2023
Perfect fit for my Dodge Durango GT 2018 and it looks great with the black accents of my blacktop edition. Easy install in only 15 minutes. Fast shipping from the seller. Arrived in good condition.
Michael Stephens
Reviewed in the United States on January 6, 2023
Took a bit to line up the factory screw holes, install time was about 45 minutes, but looks great on my 2022 dodge Durango RT
N
Reviewed in the United States on May 21, 2022
Does not fit Dodge Durango 2021. When you put in your vehicle spec, the web site says that it matches. This is my last attempt with an AVS hood shield. I am afraid a factory $150 hood shield is required.The 4 install screws holes do not line up with the Durango 2021 hood. Maybe pulling the hood weather strip plastic studs would work but I did not want to compromise my weather strip. And no plastic clips were provided.The other AVS hood shield available attaches with a top and bottom adhesive strip which in a hot wet climate I doubt will hold the hood shield for long and the risk of paint damage due to water under the glue strip.Nice materials is all that I can say positive about this purchase and return.
Joecelle
Reviewed in Canada on September 21, 2021
Your car would be more worth of a second look and it really does its job super hard and easy to install make sure you got the right alignment and you should be good
Darrel 'Knotty' Mauzy
Reviewed in the United States on April 20, 2021
I'm mechanically inclined so installation was a breeze, but I believe anyone could do it. The quality is excellent. A perfect fit. Holes lined up!! Other vehicles & other visors in the past didn't go so well and had to make adjustments. Not the case with this one. Very satisfied!!! Highly recommend.
SRZ
Reviewed in the United States on October 1, 2020
Sleeker than most I’ve had and solid. Easy 10-15 min install. No double sided tape on this one. Just requires 4 screws and plastic washers (come in the package) that replace 4 factory inserts holding the hood gasket. Just be careful not to over tighten as you can strip the thread the screw makes in the existing holes you remove the inserts from. Avoid the temptation, doesn’t need to be so tight to be well secured.
Michael
Reviewed in the United States on May 20, 2019
2019 Dodge Durango SXT. Nice piece and good value for the money. Liked this one over others since it screws into existing holes in the hood. First one I received was broken. Be mindful of this since there’s no padding in the shipping box. Read the directions carefully and don’t be in a rush since getting this on requires some patience and time. Attaching it was semi easy. I used a panel pry tool to remove the fasteners in the rubber gasket. You could use a small screwdriver. All holes lined up but u may have to bend it a little into position around the edges. The tricky part was closing the hood. The bump stops need to be adjusted. This part takes a little time and a few tries to get it right. This is one of those installs you do when your not rushing. Overall nice piece. Not sure if the screws are stainless steel to prevent rusting. I did download the instructions from the manufacturer website prior to receiving it just to familiarize myself with installation.
Glen Gibson
Reviewed in Canada on April 16, 2019
Product as described
Recommended Products
![Auto Ventshade [AVS] Bugflector II/Hood Shield | Fits 2010-2025 Toyota 4Runner, 1 pc. | Dark Smoke - 25053](images/loading.gif)