Your cart is empty.
Your cart is empty.No one enjoys scrubbing off stubborn, dried-up bug guts after a long road trip. That’s where the Bugflector II comes in. The high-profile wrap-around design provides maximum protection from all bugs, big and small, while its off-the-hood design allows for easy cleaning and waxing. Made from durable impact-resistant acrylic, the Bugflector II can stand up to everything from car washes and bugs to the wear and tear of daily driving or going off-road. Custom-molded to fit your vehicle’s exact year, make, and model and contoured to fit the curves of your hood. Available in dark smoke finish and proudly made in the USA with global materials
John Hedgecock
Reviewed in the United States on May 15, 2024
Super easy install. looks and fits perfect on my 2009 Ford E-350 van. If your hood doesn’t close after the install, remember to adjust up or down on the 2 huge rubber hood stop screws on each side of the front of the engine compartment that determine the height of the hood when latched a couple turns up or down will do the trick. Great seller too.
Clint G
Reviewed in the United States on November 9, 2024
Fits "nearly" perfect.In general this fits 100% but I did elongate the holes side to side to give me a little adjustment room.My driver side was a little tight to the headlight edge so I could move it toward the passenger side a little to gain room, and it was perfect.Well made great item for our 2018 dynamax isata4 31ds, ford E450 chassis.
les gerber
Reviewed in the United States on October 24, 2024
Works great. The self tapping screws are worthless. Had to predrill holes then use the screws provided. No big deal . I would buy again.
Bob C.
Reviewed in the United States on August 28, 2023
One of the reviews said it took his mechanics a short time to mount. Took me about an hour in 87 degree heat. Good thing I had tools from removing a door panel to remove the plastic clips holding the rubber gasket on the bottom side of the hood. Only had to drill 2 very small holes on the underside of the hood to secure the plastic hood at both ends. Looks very good once mounted, hope it keeps bugs and rocks from my windshield for upcoming trip.
iceman
Reviewed in Canada on March 15, 2023
everything was 100 % great , very good support
Leonard S
Reviewed in the United States on December 23, 2023
Fitment: There is some confusion in the reviews about which vehicles this part was made for. I installed this on a 2019 Ford E450 C-Class Motorhome chassis, but also fits a few other years/models. See my photo for the parts application sticker that came on the deflector for details.Install Tips: The included instructions are decent. It took me about 20 minutes. Take your time and review the drawings for an easier install. Start by removing just the four specified under-hood rubber strip clips. These clips will not be reused.The four larger under-hood mounting screws are self-tapping, so you just need a large size Phillips screwdriver to tighten those.Always wait to install the two outboard screws after installing the main four screws. Even though they call the two outboard screws "self-tapping", they are not. Thanks to other reviewers I had a drill and 1/8” drill bit ready to go.NOTE: Be super careful to only drill (about 3/8" max) into the underneath part of the hood; and not up through the top surface of the hood!Finally, remove the tape film to expose the two-sided tape adhesive only AFTER drilling the holes, and then install the four provided rubber bumpers to keep the thinner end sections from fluttering and hitting the hood at speed.Fit and Finish: After installation I closed the hood and noticed that the deflector is off-center about 3/8” (toward the driver’s side) where it almost touches the chrome grill. Clearance on the pass. side is ok. I may decide to carve/sand that edge back for more clearance later on. I can imagine it is difficult for the manufacturer to perfectly mass-produce an acrylic molded shape every time.Final Thoughts: The deflector definitely looks like an "add-on" but for me it is more about the function than the appearance. I expect (hope) it works to keep bugs, and more importantly rocks, off the windshield.
Sam
Reviewed in Canada on October 13, 2023
The media could not be loaded.
Page
Reviewed in the United States on March 14, 2022
This product installs just as outlined in the instructions, in about 15 minutes. The 4 large screws self-tap into the existing plastic plug holes, in the center of the hood, where the weather strip is mounted. My only issue with installation was that the smaller "self-tapping" screws on each outer end, did not self-tap. My attempts to self-tap resulted in the screws being worn dull at the tips. While I had to drill a small holes, in order to start the two small screws, dropping a star for something so minor would be disingenuous. I touched up about 30 paint chip spots before installing, so this will be well worth its price. Save the rubber bumpers that get adhered to the hood for the extreme ends. The deflector is sturdy enough, I don't anticipate hood contact in the middle area.
Josh/Tara Tolbert
Reviewed in the United States on October 13, 2022
Judging by the comments, it was hard to tell if this would fit my 2022 E-350 knapheide KUV cutaway van. It fit perfect. I hate the old man look. But I couldn't stand the extreme amount of stones and bugs that I have gotten with this brand new vans windshield. It works, maybe not perfect. But it seems to have brung the ratio back to a normal vehicles windshield amount. I hate the look, but... it needs it, and this works. Thank you
Lukdez
Reviewed in Canada on March 30, 2021
Excellent
Laura F.
Reviewed in Canada on November 7, 2020
It was exactly what I wanted
Ken bosch
Reviewed in Canada on March 9, 2016
looks great and easy install about 10 min
J. DAVIS
Reviewed in the United States on July 6, 2015
According to the Amazon information, the AVS 25016 bug shield was not a fit for the 2014 Ford E-series vans. According to another website chart, the AVS 25016 Bugdelector II fits the 2011 to 2015 (and probably the 2016) Ford E-150, E-250, E-350 and E-450 van chassis. Based on the other chart, we ordered it from Amazon and it fits perfectly. The instructions are simple and the most difficult part was removing (only 4) plastic fasteners holding the weather strip to the hood, then slipping the bug shield between the underside of the hood and the weather strip and aligning the holes. All parts are included for the install. Suggestion, place an old sheet or carpet across the top of the motor to prevent losing a small piece in the motor compartment. Installation took about a half hour. Amazon needs to update their chart information annually.
Recommended Products
![Auto Ventshade [AVS] Aeroskin / Hood Protector | Fits 2019 - 2023 Ford Ranger, 1 pc. | Smoke - 322166](images/loading.gif)