Your cart is empty.
Your cart is empty.Astro Pneumatic's 219 ONYX 3pc Die Grinder Kit includes the 1/4-Inch 90-Degree Angle Die Grinder, 1/4-Inch Mini Die Grinder and an 8pc. Double Cut Carbide Rotary Burr Set. Features of this set includes a lever throttle for feathering control, a rib textured handle which provides a firm grip and a rear exhaust air flow system that directs air away from work surface. Additionally the increased motor size provides more power to make completion of work that much easier.
Robert G.
Reviewed in the United States on March 10, 2025
Must have in your arcinle
Dead
Reviewed in the United States on February 1, 2025
I'm constantly using the angle head, for tight spots
Matt
Reviewed in the United States on September 13, 2024
Works if you oil them. I had trouble out of the box with them not turning til I worked some oil in. Also missing a wrench, but I called Astro and they mailed one out free of charge. The bits are sharp and cut anything.
Kyle Fake
Reviewed in the United States on February 7, 2024
... and the first thing you do is send it back for a replacement, you might not be qualified to be using power tools.It's an air-motor, it's not broken in yet.1. Oil it generously (with an air-tool oil... I'll spell it out for the slow guy in the back who said his replacement was also "frozen").2. WITHOUT a bit in the collet, and NOT hooked up to air, squeeze the trigger fully and hold the tool upside down so that oil can enter the tool.3. Spin it by hand several times in the direction it normally spins (CCW if you're staring down the barrel) to get everything oiled and moving.4. Set your air pressure to the max this motor is rated for, 120 PSI. Don't chuck any bits just yet, since it might still need a hand spinning up.5. Hook up your air line and go full throttle. If it didn't spin, just keep the throttle on full and give the collet a nudge in the right direction. When it is spinning, keep it spinning, but turn the pressure down on your compressor or regulator to the motor's minimum of 80 PSI. Keep it running for another minute or so, and it's good to go.
Nick Rajaee
Reviewed in the United States on December 17, 2023
These work great in my shop!!
Placeholder
Reviewed in the United States on May 20, 2022
Very comfortable to hold and they have allot of fine control with the trigger, very quiet as well. Use them at work every day and they are worth every penny, much better than Mac or snapon in my opinion. The burr set is also very useful as well
jordan
Reviewed in Canada on January 18, 2022
I mainly use the 90° for everything, no complaints it does what it needs to do, super quiet compared to my co-workers.
Dave
Reviewed in Australia on March 17, 2021
I have had minimal use so far but both the drivers and dies have performed well. I had to elongate a few holes in 6mm plate by a few millimetres not a problem, could put on a decent amount of force before they would stall out. Happy with the purchase.
blake ryals
Reviewed in the United States on January 16, 2020
I love this set! the grinders are great, especially for the value. You dont get too much torque with these and they only have a one year warranty, but the feel in the hand is great. They dont get cold like the economy metal handled tools. Theyre fast, compact and light. I just love them. They also dont vibrate in the hand a ridiculous amount like some die grinders ive had. The greatest surprise about this kit was the carbide bits though. I was expecting them to be pretty disposable and overall not that great, but they are wonderful. Very sharp and hard and have held up to everything i have put them through so far.
Spevak family
Reviewed in the United States on February 28, 2019
Both units work pretty well and the included bits have held up great as well. I did buy a second set of bits to keep my aluminum and steel bits separate and I use these ones on steel and stainless and they've held up great. The grinders themselves work pretty well. As others have mentioned, sometimes they get a little hung up and won't spin but manually spinning them and then pulling the trigger seems to set them straight. I also had issues with the collet being difficult to loosen on the straight body tool and broke both the wrenches it came with. I made a set out of thicker 1/8" material and left a little more meat on the sides of the wrench and those have held up fine. Wish they just shipped with adequate wrenches in the first place. I'm also more careful to not overtighten that tool. I recently let my girlfriend use it for a stainless project she's working on and forgot to tell her about not overtightening and had a tricky time loosening it again. I'm still within the one year warranty and plan to send it back to Astro for service to see if they can replace the collet assembly for me. I suspect a burr left behind from manufacturing causes the issue for me. I called them to ask what they could do when I first had problems and 1) Got an English speaking human being within 30 seconds of calling who 2) Covered their warranty policy and estimated turn around time on repairs. I've bought other Astro tools and once had a punch set show up without writing on one of the punches in the set. A quick phone call later and Astro mailed me out a replacement with writing on the tool at no charge to me. They're California based so shipping for me is quick and affordable if I ever need to pay for it. Will be continuing to buy Astro as I build my tool collection up. They are built well enough for my needs and offered at relatively affordable pricing when compared to similar tools from more well-known companies.
Brad
Reviewed in Canada on January 18, 2019
I’m a heavy duty mechanic and I’ve been using these for a couple years now and they are serving me flawlessly!
Kevin Bryant
Reviewed in Canada on August 12, 2015
For the price, these are fantastic. The fit and finish is great, and although the die case will probably not last long, the dies seem to be of similar quality to much more expensive ones. Both tools have worked well through a few hours of hard use, which is good enough for me.One very nice feature is that both of the wrenches the tool came with are identical; each has one side for the chuck and one side for the spindle. I don't know why none of my past die grinders have been like this, but I like it.One slight downside is that although the bits have a case, the tools themselves don't, which is a bit of a pain.
MasterLee
Reviewed in Canada on February 11, 2015
excellent kit for the price. I had a problem with an air leak on the angled die grinder(90°), you can hear the air coming out from the exhaust. I've returned my first unit(major air leak) . my 8 gal compressor was working like crazy non-stopon my second unit , on the angled die grinder again (small air leak)I'm on my third kit and its still have the small air leak problem. but decided to keep it because you won't find tools at this price.and it doesnt seems to affect the performance of the tool like the first one I hadthe rest of the kit is perfect, I never had air leak on the straight die grinder.excellent carbide burr set
Recommended Products
$73.95
$ 32 .99 $32.99
$139.00
$ 55 .99 $55.99
$104.67
$ 50 .99 $50.99