Your cart is empty.
Your cart is empty.Allen’s Antler Mounting Kit is a sturdy plaque with a wood grain laminated finish and an engravable plate. Includes a skull cover that can be formed to most horn configurations.
Trina Woolard
Reviewed in the United States on February 6, 2025
Got the replacement and it was a lot better than the first. Can’t wait to attached the antlers to it.
Becky
Reviewed in the United States on September 17, 2024
Great product our 20th purchase of these
Frank Colvin
Reviewed in the United States on November 26, 2023
Nice product and very easy to mount your deer antlers on
Ralph W Barker
Reviewed in Canada on December 9, 2021
It is probably best to make a plaque out of real wood and the Asian board blend has to be pre-drilled, otherwise there will be problems with the screws. It was actually a fair amount of work to modify my 8 pt rack using the dremel. In addition, I dug out most of the stryofoam cover and got fairly good results with the $ 29.46 kit plus tax.
RobT
Reviewed in the United States on November 9, 2021
For starters I had mixed feeling when I ordered this horn mound for the reviews I read had neg and positive notes. Had a deer rack from couple years ago that I finally decided to mount up. Upon checking the product out and materials I wasn’t sure how it would turn out, while trying to screw the bracket straps down the screws twisted right off, which was one the things I read review about, so you’re then left with pre drill a hole and find and use a screw that won’t come through the board. the middle piece is a formed out of styrofoam and absolutely would not fit over my horned correctly. Required me to have to cut of more of the scull basically up to base of horned then had to keep fit testing and cutting out of the foam to finally get it touching the board. You should just find right size bit and pre drill everything prior to install. There are no holes in the back showing where to place the hanger bracket so you will have to measure and mark that out and drill holes where needed for hanger nails slightly. The mounting board however is nice and heavy material, just need better hardware to accommodate it. If I weren’t a bit of a McGyver then I would have been lost but with my state of mind and the price was great I made it the best it can be I think. So where the picture shows paradors, this was still going to show after mid section was in place so I wrapped around below the base of horned and hot glued the ends whatcha think? All in all good product for the price just need to improvise..
Anonymous
Reviewed in the United States on January 9, 2020
Just what we wanted. Nothing glamorous. Just a simple antler mounting kit. Probably would not work well for larger/older deer with thicker skull plates. Anything older than a 3 1/2 year old would be pushing it as likely would mule deer.
Julie Tresnak
Reviewed in the United States on December 31, 2019
This did the job but since we did not have skull only the antlers my husband got creative with the mounting. Cover never did fit flush but we made it work
mike higginbotham
Reviewed in Canada on December 19, 2019
i have bought these before so i knew what they are like. They are not a high end mount but if your looking for something to put your horns on for the garage its perfect
A.f
Reviewed in Canada on November 27, 2018
Save your money it’s garbage .it might work if you get a spike buck , the cover doesn’t cover the skull shows about 1.5 inches on each side , the Plaque is cheap the screws just fall out
Greg Gawrelitza
Reviewed in Canada on July 1, 2017
fast shipping, great product
DixieChic
Reviewed in the United States on February 5, 2017
Good product. I had to adjust the foam and make some minor adaptations. This is no fault of the product but the buck. Looks nice as a finished product.
Customer
Reviewed in Canada on December 22, 2016
Very good product for the price.I would use it again
Ramone
Reviewed in the United States on July 20, 2012
I read the reviews before and I thought well, opinions vary. There are some good reviews and some bad, but I'll try it. What did I find out? This product is not worth the money!!!! The mounting system is a complete joke. When I opened the box and looked at what they provided me to mount my deer antlers, I thought, really, is this the best they could come up with, two brackets you use to screw in. I was looking in the box to see if they added a big role of tape to help me mount the antlers. Actually, that would probably work better. Maybe I'm being too hard on this item. This is the first mounting kit I have purchased, but the mounting system does me absolutely no good. I will have to come up with my own way to mount my antlerless. The rating says it all.
Recommended Products
