Your cart is empty.
Your cart is empty. The board is of high power MOS trigger switch driver module and control board with field-effect tube to adjust the electronic switch. It adopts double MOS parallel active output to show lower internal resistance,greater electric current and power. Besides it works at 15A,400W under common temperature which satisfies most devices usage and realizes the control of great power devices in a relaxed way. What’s more, it can be applied to powerful devices which could be controlled by output terminal like electric motors and light bulbs to control the speed of motor and the light of bulbs.Certainly,you can apply it to devices which could input PWM for control like LED light belt,DC motor,Micro pump and solenoid valves.
Technical Specifications:
Operating Voltage: DC 5V - 36V
The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support
Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W, Enhance cooling conditions, the maximum current up to 30A
Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc., can input PWM, control motor speed, lamp brightness and so on
Operating temperature: -40-85 ℃
Dimension: 34mm x 17mm x 12mm/ 1.34×0.67×0.47 inch(L × W × H)
Package includes:
5 X MOS FET Trigger Switch Drive Module
FixitagainTim
Reviewed in the United States on March 11, 2025
It is not capable of 30 amps! It overheat heavily and died within minutes while only handling 10 amps. Terrible product.
Customer
Reviewed in the United States on February 22, 2025
Using it to control a train set frome home assistant. Works great
Bill
Reviewed in the United States on January 14, 2025
I use these with an Arduino nano to control DC water pumps. PWM can control pump output needed.
Dave-by-the-Beach
Reviewed in the United States on May 29, 2024
Of course the first one I ever used had one defective MOSFET that always passed full current. If it wasn't the first one I would not have wasted so much time trying to figure out why NONE of my control circuits were working.Note To Self: New = Untested SuspectThe others were fine, and I even figured out which MOSFET was bad on the first one and cut the leads (now it's a 15amp module I guess) Otherwise, works as advertised!
Herve D.
Reviewed in the United States on May 23, 2024
Product is as described, work perfectly. It's even smaller than I was expecting which in my case is perfect.
George J. Francis
Reviewed in the United States on November 12, 2024
Great for one-off projects or lab use to drive lights, fans, relays, or other moderate current loads using logic levels (from an Arduino, etc).
jb9
Reviewed in the United States on October 14, 2024
First off, I see no issue with the soldering. Each component is correctly soldered on in the correct place. Second, yes, ground is switched, as you can see on the backside. This module allowed me to take the pwm signal from an ESP32 and make it work for 12V white LED lights using WLED. Easy to connect, very straight forward. 10/10
Brandon
Reviewed in the United States on October 13, 2024
Take this with a grain of salt because I am not an EE, but I was not able to drive this with software PWM from an esp32 at 3.3v, I had to add a transistor switching 5v to get there. Then I tried to configure this for 10khz pwm (to eliminate audible artifacts of the solenoid I was driving) and it would just latch on at full power, despite a clean looking PWM output according to the scope. Disappointing because this dramatically increased my part count for what I was hoping would be a straight forward project
Recommended Products
