Your cart is empty.
Your cart is empty.Product Description
Alex
Reviewed in the United States on January 11, 2025
Prints stick great and come off easy when cool
D. Gong
Reviewed in the United States on September 21, 2024
Received 2 plates, one smooth with fixed design, other textured. Smooth plate left nice effects on print. Both plates seem to be of solid build. Used Bambu special effects sheets on textured plate and works great. Nicely packaged as well.
カスタマー
Reviewed in Japan on June 29, 2024
なんでかわかりませんがきれいに色まで移ります。。。しかも何回でも移りますなんでですか！？底に映るので配置を考えないといけないんですけどきれいな模様と色になるので気にっています。。。
カスタマー
Reviewed in Japan on June 29, 2024
きれいな模様と色が何回でも出せます・・・色まで移る理由は正直わかりませんがきれいな色が毎回出るので楽しいです。
manu
Reviewed in Canada on May 12, 2024
Not the good site for an Ankermake M5C
Kelsey
Reviewed in the United States on December 6, 2024
After I accidently ran my daughters 3D printer without the plate on it, I needed to order something quickly that included the pad underneath. This was perfect and both parts have held up really well after several months of use!
Jeff Schulmeister
Reviewed in the United States on December 18, 2024
I was excited to try a new PEY build plate due to the lower bed temps needed for better adhesion over a PEI plate. Well, when I opened the cardboard sleeve that the item was placed in by the manufacturer, I found that 2 of the corners had been damaged, causing some of the bed film to curl and lift in those spots. After a few attempts, I finally got a print to stick after dropping my bed temp to 50* vs my normal 60* on PEI.Update.... Can't get anything to stick anymore. Cleaned it with soap, water and isopropyl alcohol, added a light layer of bed adhesive, but it peels up over and over again. I'm returning this and going back to the textured factory bed.
Mark Messmore
Reviewed in the United States on December 12, 2024
I picked the 330x330mm PEY+PEI build plate as a replacement for the one that came with my Neptune 4 Plus. The original STRUGGLES to adhere and I always need to use some solutions for it to stay on. This one, however, has TREMENDOUS adhesion. It is working precisely the way I hoped.
MikeFromDayton3D
Reviewed in the United States on October 23, 2024
Good quality, adhesion and functionality is great. The appearance really gets people talking with all that sparkle
Bill
Reviewed in Canada on August 3, 2023
The media could not be loaded.
Anthony Saxton
Reviewed in the United States on August 15, 2023
It works perfectly well on my printer! One flaw though is that it was shipped with protective plastic coating on the PEI side, but no notice of it. A simple solution would be to adhere a sticker on the surface with a notice to remove before use. I discovered it when it blistered anywhere the hot-end paused during the 1st layer. I submitted a return before figuring it out. Of course, I canceled the return.
みねかぜ
Reviewed in Japan on December 17, 2023
これまで純正プレートやガラエポFR-4等を試しましたが、密着性が安定せずプリンターを買い換えようかと困っていました。が、これは最初のプリントから問題無し（ザラザラ面の方）です。良い買い物をしました。
E. N. M.
Reviewed in the United States on October 24, 2023
I ordered this sheet for my mk4 three separate times. All arrived with defects.The first had a half circle cut slightly above center. The second had a dent directly in center. The third one had scratches off center. I kept the third one. I figured this was the best it would get.Pros: this does give a glossy reflective bottom layer. You can feel the layer lines, but it looks smooth from certain angles.Prints are easily removed and did not leave any marks on the bed.Cons:I printed a square 2x3” item with rounded corners. All four corners lifted during this 65 minute print. On the second print, I gave the plate longer to acclimate to the bed temp. Same results. The PEA surface has poor adhesion.Thin metal sheet. It hardly sticks to my magnetic bed. You can easily move it around.I made a print with embedded magnets. I heard a sound and saw the magnets were rattling UP towards the hotend since the plate was not magnetic enough. I’ve printed hundreds of this same model and never had this problem with any other build sheet I’ve ever used. The magnets were two layers away and shouldn’t have had a problem sticking.The removable sheet hardly grips the bed. You can easily slide it off. I wouldn’t trust this for longer prints.I ordered this 3x times. Each one arrived with a defect. Poor quality control.Notches aren’t perfect for mk4. It works but it’s skewed.The reflective bottom is a cool sounding feature. The PEA material also seems resilient. The overall performance is poor.Overall I wouldn’t trust this for longer prints. It has poor adhesion and isn’t thick enough metal for my bed to properly hold it in place. I did not try the textured side. I anticipate that side to be worse since the pea side is thicker than the textured side.
Recommended Products