Zip Line Kit for Kids and Adults, 100/120 / 150/200 ft, Up to 350 Lbs, Rustproof Stainless Steel, Quick Setup with Ratchet, Safety Harness, Backyard Adventure Fun Includes Climbing Holds

wont be able to use until summer so don't even know if all of the parts are there. Sure looks fun. Will review later in summer

We’ve got them a trampoline, then a rope swing now with this zip line there won’t be an ounce of fear their lives just adventure and loads of fun. I’ll get on it with them from time to time that’s what granddad’s are supposed to do right. 😳😎👍‼️

Great value, very happy with my purchase!

This was a Christmas gift for my son's girlfriend's son and he was very excited to get this gift

Great fun for adults and kids. Durability & speed great.

Took two people to set up - in a couple of hours. Good quality materials. Used an old tree stand for climbing up and to have a solid surface to launch from. Definitely would buy again.

looks like alot of fun for the grandkids

Everyone who says this is easy to install is oversimplifying it. Or they already own a come along with a cable gripper which is an extra $50 at minimum for some people to use one time. They also must have installed a zip line before.What we did after many failures…..1. Attached the drop off cable on the end tree to the turnbuckle. We opened the turnbuckle up the whole way so we could tighten it up at the end. We also made sure we started as close as we could height wise as we needed it to be and secured it with a few temporary nails.2. Fed the looped end of the main cable thru the turnbuckle and secured it with the bolt/cotter pin provided3. Walked the cable to the tree we planned to attach it to and unwound the entire spool of wire4. We then put on the stopping/slow down killer spring first and fed it down the main wire a bit5. Next we put on the hand glider thingy that the kids hang onto for dear life6. Our tree was huge, way bigger than the tubing they provided, so I took an old garden hose and cut it to length of something that would fit around my tree and fed the cable through it7. At this point, the spring is on, glider thingy, and my tree protector tubing8. I pulled the cable around the tree and attached it to the other side of the cable with the clamps provided to hold it in placeAt this point, the drop off / end point is up high. Mine ended up being about 10 ft off the ground.So I start to push my starting point up my tree by grabbing my hose (that had the cable fed thru it) and slid it up the tree. I got it up to about 10 or so feet then I started to struggle keeping it in place. So I grabbed some nails and eye-balled how high I wanted to go with it and nailed 6 nails in the tree all the way around. I was aiming for a foot or two above where I was stopping. I then moved the hose/cable up until it got to the nails so it could rest on them.Now, how the hell do I tighten this thing? A few Youtube video searches, everyone just has a come along and cable gripper laying around and using that. I don’t have that….and if I bought one, I’d use it once and never again.I had a heavy-duty chain, and when I say heavy duty, I mean a chain that I can tow a car with. You could use a smaller type of chain. If you don’t have a chain, use a ratchet strap or tow strap. If you don’t have either, your going to have to buy at least a ratchet strap because the next step requires one. I wrapped my chain around the tree directly above my main cable and secured it in place so it wouldn’t move, and I could pull and put pressure on it and it wouldn’t fly offI took the extra spool of wire that they provide as a safety measure in case the turnbuckle breaks, created a small loop at the one end and clamped it down with the clamps provided. This gave me a loop to work with, be sure to tighten it!I took this to where my starting point is and about 10 ft from where I have my first clamp that is holding my loop around the tree, I attached the small cable that I created the loop with to my main cable. I took a couple of really bad pictures to try and show you.I then took my ratchet and hooked it to the loop that I had made on that small cable wire, and attached the other end of the ratchet to my chain that was wrapped around the tree and secure. I pulled the ratchet as hard as I could and then started hand cranking it to pull it tight, as tight as it could go.I then loosened the 1 clamp that was originally holding the main cable wire in place, since all of the tension is now on the ratchet and my little looped cable. With two people, we pulled the main cable as tight as we could and re-attached a clamp to the main cable. This isn’t hold as much tension as the ratchet cable, but it’s slowly progressing and holding the cable tight. I then let all the pressure off the ratchet cable, and your new clamp connection should then hold. You just keep repeating this until you get to a point where the cable is tight to your liking. We tested this by having our child go down it, cause why not.Now that you have the cable tight, pretty tight, and your child is most likely fine and doesn’t have seriously hurt feelings for wrecking their butts on the ground from testing – it’s time to tighten the turnbuckle up. If your child hurt their butts, tighten it a bit more with your ratchet strap.Turn your turnbuckle to tighten, use the nuts as a guide to know if you’re going the right direction. Don’t do what I did which was be excited cause we’re about to have a bunch of fun and think righty tighty left loosey works here cause you’ll be righty tightying your way back up to the main tree to start all over.I would tighten the turnbuckle slowly, depending on how tight you have the cable you may not have to tighten this to much.Add the remaining 2 clamps at the starting pointAdjust your seat height if necessaryHave fun!Time will tell if this thing lasts, if it will rust, or break....One of the horrible things about this unit is that the clamps that they give you start the break down using this method of tightening and untightening. It's because they are cheap, that tells me they probably won't last long and I'll have to buy new ones. I actually had to use bolt cutters to cut a pair because the nut/thread was stripped on the one when we were FINALLY done, I couldn't get the nut off. That's what she said

Everything appears to be sturdy and good quality but I struggled with the instructions and I also think the video and instructions are misleading on the difficulty of install.I will start by saying everything looks like sturdy quality parts. My kids are playing on it and having a blast. The problem comes from the instructions and video they posted.First off, you will not install this by having one buddy standing on a ladder pulling the tension out. Maybe you can get away with that on the 65' line but I had the 160' and there's no way. If you do not pull most of the sag out, then you will not be able to tension the rest of it with the turnbuckle.Speaking of turnbuckle, there is no instructions on how to tension it. I know it doesn't seem complicated, but it could have told me to make sure the turnbuckle is all the away out so you have the max amount of room to add tension which is the last step. How do you tension it? Well I guess grab some channel locks, and a wrench and figure it out while also trying to keep the whole thing from spinning because I dont recall any instructions.What elevations do you mount it? The instructions dont appear to apply to anything over 100', so I had to do some research on the web.How tight should it be? I think it just said "do not over tension". Well, you have to add a considerable amount of tension as it's key for the whole thing to work, so how much is too much?Apparently, there is a safety mechanism for the turnbuckle, but again, no instructions. I thought they were extra parts until I looked at the box.The "monkey climbers" didnt have instructions and the straps I got were orange. I figured it out but I'm assuming a lot of people dont know how to use ratchet straps. I think the monkey climbers are almost worthless. With 4 levels, a kid can only climb to the second level or step, so what is the point? To be fair, my kids did play on them a little bit. At least I have 4 ratchet straps and you may need those to help with install...I ended up buying a pulling device to tension the cable. It attaches to a come-along which I attached to two of the included ratchet straps. Dont even kid yourself into thinking you can tension the cable without it. It also makes it so much easier and safer to install, and if you decide to move the zipline, you will need it again as it's safer to remove the tension slowly with it, then letting the whole thing whip out while removing the clamps. It cost like $30 bucks on amazon and is well worth it.I wish the seat had a rope attachment through the bottom so somebody can pull you around with it. Seems to be in the box pictures but not included.

We got the package and my husband installed the zipline in less than two hours, spanning two trees in our backyard approximately 150' apart. This thing is sturdy and durable and provides HOURS of fun for our 10- and 8-year-old!! Probably the best purchase we've made for the kids EVER. Buy this!!!