Your cart is empty.
Your cart is empty.Product Description
Super Simple to Unlock Full Potential of Your Bike!
Our programming cable allows connection of a PC with the BBS01/BBS02/BBSHD mid drive motor.
The Programming cable plugs IN PLACE OF the display. So here are the steps:
- Connect the battery to the motor.
- If the battery has an On/Off switch, turn it on.
- Plug the programming cable into the connector that the display was plugged into.
- Plug the other end of the Programming cable into an USB port on your laptop.
- Now start the Bafang Programming Tool.
BBS Motor Programming Cable
Secure Fit & Strong Connector
Easy to use the programming cable and the Bafang Programming Tool to change the options of the controller for your Bafang mid-drive motor.
Embedded Smart Chip
Performance to increase battery and motor life, enable full throttle in PAS levels 1-9, throttle over ride of max set speed limit (max speed only applies to PAS)
Reinforced Programming Cable for Bafang Motors
Great reinforcement provides superior durability and better protection for internal wires. This Programming Cable is over 40% stronger than the previous model—a cable renowned for its durability.
What's In the Box?
- Programming Cable for Bafang BBS motor 40 Inches x 1
- Windows Driver for Programe Cble x 1
- Instructions for Programming x 1
- Programming Software x 1
Kindly Note
Tune your motor with the back wheel in the air or remove the chain from the chainwheel.
Basics of programming BBS02 and BBSHD mid drives
- This programming cable enables the possibility of getting more performance or having the PAS settings more to your liking.
- Access the custom program settings to dial in the performance of your drive.
40 Inches Long Programming Cable for BBS01B Motors
40 Inches Long Programming Cable for easy reaching from your desktop to ebike. No more suffering from a 22 inches short cable.
Programming cable to change the controller settings - compatible with Bafang BBS01, BBS02 und BBSHD motors!
If you own a Bafang mid-drive motor you may want to change a thing or two in the controller programming. You will need the program cable, and program software. You will also need a Windows computer to run the software.
Question 1
Question 2
Question 3
Question 4
Wolfi
Reviewed in Germany on September 6, 2024
Habe mir das Kabel für mein E-Bike mit Bafang Heckmotor bestellt.Schnelle Lieferung, sehr gute Verarbeitung, einfache Installation und Konfiguration.Hat alles perfekt geklappt und funktioniert.Anmerkungen : Um die Einstellungen vorzunehmen, sollte man schon etwas technisch versiert seinAnsonsten alles perfekt und klare Kaufempfehlung
interior photographer
Reviewed in the United States on September 5, 2024
It is not the most complicated device, but I've heard that some of the programming cables have issues. This one woks.
François Duclos
Reviewed in Canada on March 24, 2024
Works with Bafang M620 ultra motor as well!
G. Ross Francis
Reviewed in the United States on October 8, 2024
I appear to have recieved a defective cable. That is, I was unable to connect to a BB02 motor using either an Android App or a Mac program.
Mr. Mark A. Burrows
Reviewed in the United Kingdom on October 20, 2024
Perfect for use programming the BBS02 motor to a more "rounded" power profile than it comes with out of the box. Works with both my desktop and laptop machines - no issues at all.
Moises
Reviewed in the United States on April 26, 2024
Used this to program my bafang BBS02 using the Speeed App and a Chromebook. Connected to the motor controller flawlessly.
BC
Reviewed in the United States on April 18, 2024
Connected as expected. I use the Mac BafangConfigTool and Chrome. Worked great.
E. D.
Reviewed in the United States on September 21, 2023
I wondered why it wasn't working with my computer and middrive motor and ended up buying another cable that did work right away. I looked at the voltages from this bad cable compared to the good one using an oscilloscope and this one has a cheap design of a common CH340 USB board that doesn't sent the right voltages to the motor controller. Voltage when sending 0 bit is too high.
justin t.
Reviewed in the United States on September 18, 2023
was able to find the bafang software and get my motor to turn on. i have an error 30 which means my display or controller unit went. i bought a new display and guess what =) it was the controller unit that went hah. so i need to order one of them
TURTLE
Reviewed in the United States on August 26, 2023
Works great for my electric bike...It was the most resumly priced on the internet?
Paolo
Reviewed in Italy on August 1, 2023
Fa quello che deve, anche se il suo assemblaggio è di aspetto artigianale ma, non è detto che sia un male, anzi
Lasse Sundin
Reviewed in Sweden on March 27, 2023
Problemet var att cykelmotorn ej passade och denna produkt alltså aldrig kunde provas.
richard
Reviewed in the United States on February 10, 2023
depends on the program. some are out of date and othes updated. i just looked around for the latest program. the cables works just dont blame it on the cable itself. also i disconnected the battery or didnt when i flashed it. gotta follow instructions to the ""T"it didint fix the battery gauge that says empty all the time but i know about how far it will go, my bike that is. i did get the assist pedal to working again, i just used one of the provided pre settings that was in file that came with the downloadable settings program. i think the battery gauge just shorted out. igot a voltage checker at walmarts for 11 bucks, i found out my battery has full charge and was not the problem. check one problem at a time and youll figure out how to fix it.
Recommended Products