Your cart is empty.
Your cart is empty.1x OEM Black Grille Z71 Emblem Badge 3D Compatible with Silverado 2500Hd 3500Hd Sierra Tahoe Chrome
Brandon Nguyen
Reviewed in the United States on July 29, 2024
Fit our 2020 Silverado perfectly, but the only problem is that the red sticker on the Z will eventually fall off due to the poor adhesive (along with standard weather/vehicle elements affecting it). Good product overall.
Exclente producto lo recomiendo
Reviewed in Spain on May 21, 2024
Se ajusta bien se ve muy bien lo recomiendo
Victor
Reviewed in the United States on December 30, 2024
No instructions and can't put on
RickyBobbyinc
Reviewed in the United States on December 13, 2024
Nice emblem. It's metal so it will last. Not much for threads for the bolt to screw into on the emblem itself but a bit of thread locker to hold it and it's fine. Just don't go crazy tightening it.
Manuel Ramos
Reviewed in the United States on October 17, 2024
La puse con mucha facilidad y resalta en la parrilla negra.
Mike
Reviewed in the United States on April 25, 2024
Great looking grille badge, good quality, only thing that could make it better is a if the single threaded bolt could thread into the back a little more or if it had 2 bolts that thread in the back. Other than that it's Great.
Fernando Salido
Reviewed in Mexico on December 13, 2022
da un toque discreto pero bonito a la parrilla, super facil de poner, no necesitas quitar la parrilla para instalarlo, mete la mano por el gancho del cofre
Larry D. Mcclelland
Reviewed in the United States on July 25, 2021
No directions given or anywhere here or google. After looking at it I noticed 2 holes on the back of the emblem. Fine, threaded shaft will screw in to center or offset hole on back of emblem then can be placed on grill and the backing plate,nuts, and washers can be placed on the inside of grill and screwed down with the supplied nuts--I used red locktite on the emblem end and blue on the nut end.
Stephen
Reviewed in Canada on December 30, 2021
Product exactly as described. Easy installation
Colllin
Reviewed in Canada on November 13, 2019
You get what you see
marc d.
Reviewed in Canada on October 2, 2019
thank you
LungMei
Reviewed in the United States on August 15, 2018
I'm writing this review for others looking to purchase. This is a high quality metal badge for your truck. It looks great, just like OEM.The factory badge removes easily by prying it off. There are locating pins on the factory model that protrude through the grill. On some trucks (like my 2016 1500) it may be necessary to cut off or squeeze the tabs on the back so they come out of the grill. Once that is done, just pry it off. You'll see GM uses sticky tape too.On my 2018 2500HD there are locating pins on the factory Z71 badge, but they are smaller than the holes they go through, so they just come right out. Once you gently pry the old badge off, put 3M double sided tape on the back of the new one, line it up, and press it on firmly.I can absolutely guarantee it won't come off. My last one survived an impact with a concrete wall at 60 mph thanks to some non driving idiot. Despite the near death experience for me, the Z71 badge stayed affixed perfectly to the grill.The point is, these are super easy to install. The clamp is not even necessary. Just some sticky tape and you're good.
Eddie V.
Reviewed in the United States on June 11, 2017
The look and feel is spot on. The only thing I feel is a flaw is the mounting hardware. The emblem has 2 threaded areas for the screws. The problem is there is only one screw with only one hole for the screw in the bracket (exactly as pictured). I went to my junk bin and found a screw that had the same thread pattern and drilled the second hole into the bracket. I'm pretty sure that the one screw would have been sufficient but I didn't want the emblem to twist so that's my reasoning for using a second screw.
Recommended Products
