Your cart is empty.
Your cart is empty.
Yakamoz 1/4" Shank Rabbet Router Bits Set
✔Kickback reducing design
✔Individually Computer balanced
✔Precision ground for the smoothest cuts
✔Easy to use
✔Perma-Shield coating to resist heat
Specification:
◆ Material: Carbide Tipped
◆ Rabbet Cutting Depths: 1/2", 7/16", 3/8", 5/16", 1/4", 1/8"
◆ 6 Bearing Sizes: 3/8", 1/2", 5/8", 3/4", 7/8", 1-1/8" with inner diameters of 3/16".
◆ Shank: 1/4 Inch
Package Includes:
1 Set Rabbet Router Bit
Cole H Stott
Reviewed in Australia on February 5, 2024
On-time guarantee
rlkiser
Reviewed in the United States on June 19, 2023
Excellent quality, works perfectly. Absolutely no complaints.
Paul Hill
Reviewed in the United States on January 18, 2023
Nice idea, and cheap to buy, BUT... The largest bearing was really not usable, very unstable and poorly made. I used it once and considered myself lucky; I will retire it now. The cutter is fine, and I haven't used the smaller bearings although they look better. I need it for cutting guitar binding ledges, and ended up spending $120 on a set from Amana.
AlpineMan
Reviewed in Australia on September 13, 2022
Arrived next day and worked perfectly. For the price the quality is excellent. Would highly recommend
Adrian
Reviewed in Australia on December 28, 2022
Very disappointed with this bit. I was using it with the smallest bearing on half speed and after about a minute the bearing disintegrated resulting in my work being ruined. You can see the remnants of it in the picture I uploaded. It could have been more dangerous with the larger bearings, hence I will be sending it back for a refund. It is a shame because the bit cut nicely.
P. Jones
Reviewed in the United States on July 19, 2021
I used this to put a rabbet in the bottom of a box to put an inset base. Needed slightly more than .50" rabbet. Did it in two passes. Worked perfectly. Clean cuts; No drag or binding. Even cut cleanly through a knot I foolishly placed at the bottom of one side. Oops. Don't know how it will perform over time, but I'm hopeful. Great price and well worth it.
Trevor Merton
Reviewed in Australia on February 17, 2021
Great looking product and well presented
Andrew
Reviewed in Australia on August 9, 2020
Purchased to do some small rebate cuts, and needed the largest bearing to achieve this. But the bearing hits the cutting blades as the spine isn't raised enough for it to spin freely. Useless and poor design.
Wood_fly
Reviewed in the United States on May 5, 2020
The screw isn't precisely machined so is a little tough to screw/unscrew when changing bearings (yes I cleaned it out). But the cuts are accurate. The lack of shear angle means taking smaller cuts is recommended vs hogging out much over 1/8" at a time, but it works fine.
j barre
Reviewed in the United States on August 13, 2019
I have rabbeted about 50 feet of cabinet backs with a Dewalt router at speed setting 3 and the results are good. Clean cuts, no vibration and no tear out. As long as I don't run this bit at to high a speed I think the sharpness will last. The wrench that comes with the bit doesn't fit tightly so I used a 2.5mm wrench to loosen the bolt so I could change bearings. The bolt took considerable effort to initially break the torque, nothing I haven't encountered with other new bits.
Brando_Squire
Reviewed in the United States on July 22, 2019
Great bit. It cut through the Douglas fir I was using like butter. I made a rookie mistake by having the bit extended too far and Yakamoz offered to replace or reimburse me. Definitely a good company to buy stuff from. I’m getting a new set of bits from them and I can’t wait.
Mark Richards
Reviewed in the United States on November 6, 2019
I am quite happy with this. Allows me to do rabbits of multiple sizes with a single bit. Easy to adjust, and it comes with a handy spindle for holding the bearings not in use. Seems reasonably sharp, but not super sharp. About what I expected for the price.
A
Reviewed in the United States on January 27, 2019
Bit may be inexpensive but it served it's purpose well. I used this while making 4 table saw inserts. My plywood was too thick so i used this bit to cut a rabbet so the insert would sit flush. Plywood is rough on router bits and this survived 4 inserts. So the bit has paid for itself when considering the cost of factory made inserts. 4 inserts would have cost over $100. The only issue is some of the yellow paint flaked off so minus 1 star but really a great deal when compared to cost.
Recommended Products
$16.95
$ 6 .99 $6.99