Shopping Cart

Your cart is empty.

Your cart is empty.

WMYCONGCONG 8 Pcs KY-040 360 Degree Rotary Encoder Module with Knob Cap for Arduino Micro Controller Use

Free shipping on orders over $29.99

$12.59

$ 5 .99 $5.99

In Stock
  • The rotation counts are not limited, designed with continuous 360 degree rotation sensors.
  • Working voltage: 5V
  • Material: Electronic components + PCB
  • Reset to its initial state with the buttons on the rotary encoder, starts counting from 0.
  • Designed with detent and push button switch feature, comes with nuts and washers, suitable for Arduino micro controller use.


Specification:
KY-040 Module:
Working voltage: 5V
Pulse circle: 20
Material: electronic components + PCB
Size: 26 x 19 x 29mm/1.02 x 0.75 x 1.14inch
Diameter of the thread: 7mm/0.27inch
Height of the thread: 7mm/0.27inch
Knob Cap:
Diameter: 15mm/0.59inch
Height: 16.5mm/0.65inch
Connection:
"GND”: ground terminal
"+”: 5V power supply
"SW”: 'Select' switch (activated when shaft pressed on top)
"DT”: Encoder Pin B
"CLK”: Encoder Pin A
Designed with detent and push button switch feature, comes with nuts and washers, suitable for Arduino micro controller use. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer counter, which species rotation counts are not limited. How it works: incremental encoder is a displacement of the rotary pulse signal is converted to a series of digital rotary sensors.
Package Content:
8 pack KY-040 rotary encoder module(knob, nut, washer included)


Juan Jose Vanegas
Reviewed in Canada on January 24, 2025
The encoder caps were extremely scratched up. Also not a single piece of foam, everything is just loose.
Bob
Reviewed in the United States on September 23, 2023
Works great with Arduino!
Christopher Getsfred
Reviewed in the United States on September 16, 2023
I used these along with a Raspberry Pi Pico W to create a button panel for sim racing. I use three rotary encoders to control brake bias and front/back anti roll bar. Works like a charm.
allen jacques
Reviewed in Canada on August 25, 2023
I am building a robot lawn mower and use these as position sensors with arduino. work great!
Shane
Reviewed in the United States on January 28, 2023
As yet untested but appear to be of good quality. Quick delivery with great packaging.
Beaky
Reviewed in the United Kingdom on June 30, 2021
Hmm. This product could use a deep socket nut so it could be built into 3/8" front panel hole. Am improvising. It will work with an embedded microcontroller and act as a coarse sweep switch on an oscilloscope where the micro generates the sweep waveforms. It is elegant !
Peter Frier
Reviewed in the United Kingdom on June 21, 2021
Quick delivery, good price, and work okay. These encoders have pull up resistors built in to pcb.
Bobby
Reviewed in the United States on September 24, 2020
Great encoders, these have the two resistors on the back side, I’ve had previous encoders that only had a single resistor and they gave me issues with my menu system. These seem to solve the problem for my spot welder. Great product
Bill P.
Reviewed in the United States on September 3, 2019
One click is registered as two. Maybe I'm using it wrong or have the wrong idea of how a rotary encoder should work but I had to account for that in the software I'm writing that reads the value of the encoder.The knobs look good and match the knobs of the potentiometers I have. They're easy to wire up and there are quite a few Python modules for reading the values.
Rob
Reviewed in the United States on July 10, 2019
exactly as expected and works as initended
Kathleen Taylor
Reviewed in the United States on September 13, 2018
These are actually quadrature encoders. They function well; however, none of the documentation matches the labeling on the device. With a little trial and error you can hook them up and they work great. No switch bounce that is normally found in mechanical encoders. They are very inexpensive.
Taylor
Reviewed in the United States on December 20, 2018
Documentation for this is not with the product but it's easy to find online. works well. No issues with speed.
Recommended Products

$15.99

$ 6 .99 $6.99

5.0
Select Option