Your cart is empty.
Your cart is empty.Product Description
Carbide End Mill Cutter
Made of solid carbide (tungsten steel), high hardness, wear resistance, good toughness and heat resistance. Provide good cutting strength and drilling effect to improve efficiency.
Spiral and Sharp Flute
Spiral chip space design for fast and clean chip removal. Sharp cutting edge provides smooth cutting and no glitches.
Upcut Design
Upcut end mills can direct chips up and away from the milling area, leaving an unobstructed path to prevent tool breakage and extends the tool life.
Features
- Carbide can run at higher speed than high-speed steel.
- Designed with the base substrate without any coatings, suitable for wide ranges of applications.
- Different spiral end mills are available to meet your needs.
Wide Applications
Suitable for engraving, cutting, carving, milling, slotting, sculpturing in MDF, ABS, PVC, acrylic, nylon, plastic, wood, plywood, hardwood etc. Good for surface machining, 2D or 3D relief sculpturing. Use on milling and engraving machines. Use vertically and take good control of your CNC speed.
Felix Sapien
Reviewed in the United States on March 17, 2024
I use these in my Genmitsu PROVer XL 4030 CNC machine with a Dewalt 610 spindle. With my new spindle, I am able to cut out the project I use these bits for in half the time. Time saved is money made. I couldn't be happier with them. It's a good thing they come in a pack of 5. I have been known to snap one here and there, not the bits fault.
Randy
Reviewed in the United States on February 15, 2024
If you are very careful. I'm side milling 4mm deep slots at 10,000 RPM. I'm going pretty slow with manyu passes - 0.05mm DOC at 1mm/min. I can probably go faster but I only needed to do two slots. Use lube like WD40!
Steve R
Reviewed in the United States on November 1, 2023
Used on my CNC machine for fine lettering/designs in hard woods. I have over 5 hours on them so far and they are still extremely sharp. They make nice clean cuts. I did break one when it hit a clamp (totally my fault).
G baker
Reviewed in the United States on October 19, 2023
Cut and held up really good would buy again
Mattson
Reviewed in the United States on January 26, 2023
These worked great for my CNC project, and cut cast plexiglass fantastically. The tiny diameter means you may break a bit or two, but that's why you buy a pack of 5!
Miguel C.
Reviewed in Spain on April 24, 2023
Las fresas cortan muy bien. Se pueden hacer trabajos muy precisos con ellas.Ajustar bien los parámetros de vuestras máquinas, porque al ser tan finas y largas, es muy fácil romperlas.
SEM
Reviewed in the United States on August 28, 2022
Two flutes up-cut. Worked well with no issues. The cutting length is reasonable, which helps to not snap them off so easily, like the ones with the crazy long spiral cutters. Would buy again.
NP
Reviewed in the United States on August 27, 2022
Used it to carve out a groof to fit a floral hoop on about 20 wood rounds. Still sharp and sturdy.
markr
Reviewed in the United Kingdom on April 6, 2022
These are my go too bit when I am roughing out a 3D carve with my cnc. They last a few times and never had one break on me so makes them brilliant value. They give a good finish and handle hard woods like Oak with ease.
Boca Ron
Reviewed in the United States on March 20, 2021
I use these to cut letters into wood. Works ok if you take small incremental cuts, will eventually dull but works fine if you don't cut too deep. I use 0.006 inches per cut at 10 inches or less per minute.
serge dussault
Reviewed in Canada on February 1, 2021
bon
Djukha
Reviewed in Canada on July 19, 2020
Nice blade on look but when using them for cutting they brake. I still have several left it could be my inadequate speed or rotation but they just feel weak for now.
je suis un observateur
Reviewed in France on July 18, 2019
pour un usinage très fin c'est l'outil approprié
Recommended Products