Your cart is empty.
Your cart is empty. Upgrade Design:
Made of stainless steel. Have a more complete set of accessories, perfect fit for the model
Compatible with Jeep:
Compatible with 2020 Jeep Gladiator
Compatible with 2021 Jeep Gladiator
Compatible with 2022 Jeep Gladiator
Compatible with 2023 Jeep Gladiator
Replace Part Number:
82215956
Package Include:
3x Bed Cargo Rail
6x Bed Cleat
16x Screw
2x M6 Bolt
Kurtis Daniel Taylor
Reviewed in the United States on February 25, 2025
This is a nice, high quality kit. It was great other than one part. The crush nut is meant to compress to hold in a hex shaped hole. Mine instead started spinning before fully crushing. This made it really hard to remove. I used the correct torque spec but the nut itself was too soft. The instructions should have you wait to torque it down until the rail is installed so you don't have to remove the bolt. Otherwise a solid choice.
Customer
Reviewed in the United States on February 10, 2025
Works great and so much cheaper than the factory version. Highly recommend and looks great in the truck.
Serena
Reviewed in the United States on January 4, 2025
Very easy to install on my 2020 jeep gladiator. I did have to use a 6mm tap to clean out the holes in the bed but after they were cleaned, everything fit like a glove!
Mike
Reviewed in the United States on January 3, 2025
Couldn’t be happier with this product. All mounting holes lined up, screws went right in and torqued to spec with no issues.
Brennan McMahon
Reviewed in the United States on September 11, 2024
So if you have the factory spray in bed liner you’ll need to clean the bolt hole threads with a tap, other reviews have the tap size. then the bolts will go right in like they should the instructions are not hard to follow just ignore the photos in the instructions. They are just as nice as the factory ones and as sturdy
Bryan Sanderson
Reviewed in the United States on June 17, 2024
At a fraction of the cost of the Mopar cargo rails, I figured these were worth a try. The box came with some tape cut and re-taped but all the pieces were still present and the rails in good condition. During the install, there are four screws labelled "F" shown to attach the front rail to the bed. Looking at the part list on the first page of the instructions, there is not a "F" bolt shown. I counted the "D" bolts and there were enough for all the holes and used those instead. On the next step, it showed an arrow pointing FWD supposedly indicating the front of the truck however it was pointing to the rear of the truck. Honestly, it was pretty easy to figure out that their instructions were not correct and I was able to finish installing the rest of the rails.Overall I think these are pretty good. I have a tonneau cover on the bed of my truck so they won't be exposed to direct weather so I expect them to hold up well. I did use a tap to clear the factory bed liner from the screw holes so I didn't have any issues getting the bolts in like some of the other reviews had stated.
J. C. Branch
Reviewed in the United States on December 18, 2024
Rails and cleats are fine, bolts and hex rivnuts provided are marginal.As noted in instructions, clean out and retap mounting bolt holes if you have a sprayed on bedliner.You’ll need:5mm drill bit and 6mm x 1 plug tap to clean out mounting holes.Torx 30 bit and 1/4” torque wrench to install mounting bolts. Watch out for- over tightening installation bolts which will result in existing threaded mounting points being stripped out.Ratchets and drivers to install bolts.Instructions call out front direction for installation incorrectly.
Jewelei23
Reviewed in the United States on October 28, 2024
I am happy with the rail system. It fit my 2024 Jeep gladiator perfectly! I was nervous because it was only listed up to a 2023. I took the advice from prior reviews and used a tap on all of the holes. It was installed in about 15 minutes and was a great base for the our MOLLE panels and truck rack. Very happy with this product!
Recommended Products
